Classic British roar from a classic British stack!

This Marshall full stack includes a 1959HW head, a 1960AHW angled extension cab, and a 1960BHW straight extension cab.

Marshall 1959HW Handwired Plexi Head
The Marshall 1959HW amp head is a handwired reissue of a circa 1967 100W Superlead head. Since 1967 when the JMP (Jim Marshall Products) Plexi panels were introduced, the Superlead head has been the benchmark for all-tube distortion and tight crunch. Tube lineup includes 4 EL34s in the power section and 3 ECC83s in the preamp. True bypass effects loop, 3-band EQ, and presence control.

Marshall 1960AHW & 1960BHW 120W 4x12 Extension Cabinets
The 1960AHW and 1960BHW are hand-soldered, 120W, mono, 16-ohm 4x12" guitar speaker cabinets with salt 'n' pepper grille cloths, metal handles, loaded with reissue 30W Celestion G12H speakers.

Marshall 1959HW, 1960AHW, and 1960BHW Full Stack Features:

• Marshall 1959HW Handwired Plexi Head
• Handwired reissue of 1967 Superlead
• 100W
• 4 EL34 power tubes
• 3 ECC83 preamp tubes
• True bypass effects loop
• 3-band EQ
• Presence control
  
  Marshall 1960AHW & 1960BHW 120W 4x12 Extension Cabinets
• Hand soldered
• Mono
• 16 ohms
• Salt 'n' pepper grilles
• Metal handles
• Reissue 30W Celestion G12H speakers

Don't settle for less...if you want massive Marshall sound, this is the rig. Order now!

The real screamin' deal!

This Marshall Full Stack includes a 1959SLPX Vintage Series 100W Tube Head and 1960AX/1960BX 100W 4x12 Guitar Extension Cabinets that enable you to play it loud and play it proud.

1959SLPX Vintage Series 100W Tube Head
This all-tube Marshall 1959SLPX tone machine cranks out fabulous lead distortion and tight crunch exactly like the original model from the 1967 to 1969 era. Inspired by Pete Townshend's unquenchable thirst for VOLUME, this guitar amp head features 100W of power from 4 EL34s and 3 ECC83s in the preamp the exact configuration of the original. True bypass series FX loop, 3-band EQ, and presence control.

1960AX and 1960BX 100W 4x12 Guitar Extension Cabinet
The Marshall 1960X speaker cab consists of 4 separate birch ply enclosures, each loaded with a Celestion G12M Greenback 12" speaker and has a 100W power handling rating. Tonally this speaker cabinet falls between the 1960A's brightness and the 1960TV's warmth. Greenback G12M speakers have a very distinctive sound with a fast, snappy response that adds detail and dynamics to both clean and distorted playing. The 1960X Extension Cabinet uses the early '70s LC checkered grille cloth and a less-textured vinyl covering. If used as a half stack with a 100W head, a power brake is recommended.

Marshall 1959SLP, 1960AX and 1960BX Full Stack Features:

• 1959SLPX Vintage Series 100W Tube Head
• 100W
• 4 EL34s in the power stage
• 3 ECC83s in the preamp
• True bypass series FX loop
• 3-band EQ
• Presence control
  
  1960AX and 1960BX 100W 4x12 Guitar Extension Cabinet
• 4 x 12 Celestion Greenback G12M speakers
• 100W handling
• Checkered grille cloth
• Straight or Angled front
• 100 lbs

This is the original head-cutting head. Make it yours and make history.

Real all-tube vintage flavor from the original maker.

Channel the ghost of Hendrix with this Marshall Full Stack featuring the 1978XL Vintage series 50W Tube Head with 1960AX/1960BX 100W 4 x 12 Guitar Extension Cabinets.

1987XL Vintage Series 50W Tube Head
The Marshall 1987XL Vintage Series 50W Tube Head gives you all the fabulous tube tone of the original 1987X from the 1966 to 1969 era plus a true bypass series FX loop. 3 ECC83 tubes in the preamp and 2 EL34s in the power section dish out that delicious, nasty overdrive behind Hendrix, Townshend, and scores of other greats. 3-band EQ and presence controls provide all the tweakage necessary to get the most out of this classic screamer.

1960AX and 1960BX 100W 4x12 Guitar Extension Cabinets
The Marshall 1960X consists of 4 separate birch ply speaker enclosures, each loaded with a Celestion G12M Greenback 12" speaker and has a 100W power handling rating. Tonally this speaker cabinet falls between the 1960A's brightness and the 1960TV's warmth. Greenback G12M speakers have a very distinctive sound with a fast, snappy response that adds detail and dynamics to both clean and distorted playing. The 1960X Extension Cabinet uses the early '70s LC checkered grille cloth and a less-textured vinyl covering. If used as a half stack with a 100W head, a power brake is recommended.

Marshall 1987XL, 1960AX, and 1960BX Full Stack Specifications:

• 1987XL Vintage Series 50W Tube Head
• 26"W x 8"H x 10"D
• 34 lbs.

Marshall 1987XL, 1960AX, and 1960BX Full Stack Features:

• 1987XL Vintage Series 50W Tube Head
• 50W of classic all-tube power
• 3 ECC83 tubes in the preamp
• 2 EL34s in the power section
• 3-band EQ
• Presence control
  
  1960AX and 1960BX 100W 4x12 Guitar Extension Cabinet
• 4 x 12 Celestion Greenback G12M speakers
• 100W handling
• Checkered grille cloth
• Straight or Angled front
• 100 lbs.

To get the real sound, go for the real deal. Order today!

A rock standard, now with impedance switching!

Get more punch and crunch with this Marshall full stack featuring a JVM410H Tube Amp Head with a 1960AV/1960BV Full Stack.

JVM410H Tube Amp Head
In a nutshell, the Marshall all-valve, 4-channel JVM410H 100-Watt tube head is the most versatile Marshall amplifier ever made. It also boasts more gain than any other Marshall to date-and that's really saying something!

Each of its 4 channels Clean, Crunch, OD1 & OD2 are not only completely independent of each other, they all boast 3 Modes, all 12 of which are footswitchable and feature their own unique gain structure. It makes the JVM 4-channel effectively 12 Marshalls in one!

The JVM410H amp head has studio-quality digital reverb with a level control for each channel. This is also footswitchable, as are the amp's two Master Volume controls and the Series/Parallel effects loop. Resonance and Presence are equipped with master controls.

Even though the head and combo both house 28 controls and 8 LED switches on their front panels, they're incredibly simple to understand because of the extremely logical layout. Each of the 4 channels has the usual suspects when it comes to controls Volume, Bass, Middle, Treble & Gain-accounting for 20 of the 28 controls right away. Take away the 4 reverb controls and you're only left with 4 Master controls-2 Master Volumes plus Resonance & Presence.

Add to this an ingenious footswitch (UK patent pending) and the fact all the amp's switching (channel/modes, Reverb, Master Volume selection, FX loop) can be done via MIDI and you're looking at an incredibly flexible amp! The 6-way footswitch boasts 7 LEDs and memory, plus it connects to the amp via a regular guitar cable.

From the cleanest clean to the filthiest distortion ever found in a Marshall and all points in-between, the JVM410H all-valve amp head will give you whatever tone you need right when you need it.JVM410H Tube Amp Head
In a nutshell, the Marshall all-valve, 4-channel JVM410H 100-Watt tube head is the most versatile Marshall amplifier ever made. It also boasts more gain than any other Marshall to date-and that's really saying something!

1960AV and 1960BV 280W 4x12 Guitar Extension Cabinet
The Marshall 1960V Vintage Speaker Cabinet puts out beautiful tone at any volume. The addition of an impedance (4 or 16 ohm) mono/stereo switching mechanism has transformed the "industry standard" 1960 into the ultimate speaker cab. This 280W Marshall cab is loaded with Celestion Vintage 30 speakers.

Marshall JVM Series JVM410H, 1960AV and 1960BV Full Stack Specifications:

• 1960AV and 1960BV 280W 4x12 Guitar Extension Cabinet
• 280W handling
• 4 x 12" Celestion Vintage 30 speakers
• Impedance (4 or 16 ohm) And mono/stereo switching

Marshall JVM Series JVM410H, 1960AV and 1960BV Full Stack Features:

• JVM410H Tube Amp Head
• 100-Watt valve head
• Valve complement: 5 x ECC83 (12AX7s) in preamp, 2 x EL34s in power amp
• 4 independent, footswitchable channels-Clean, Crunch, OD1 & OD2
• Each channel boasts 3 footswitchable modes Green, Orange & Red
• Studio quality, footswitchable digital reverb with level controls for all 4 channels.
• 2 footswitchable master volumes
• Two FX loops-Series/Parallel & Parallel
• Series/Parallel FX loop is footswitchable
• Emulated line out
• 6-way, 7-LED footswitch with memory capabilities (UK patent pending)
• All switching can be done via MIDI
• Made in England
  
  1960AV and 1960BV 280W 4x12 Guitar Extension Cabinet
• Bottom cabinet has casters and straight front
• Top cab easily stacks on top and has an angled front

No backline would be complete without the legendary Marshall 4x12 cab. Order now.

Marshall roar - 1967 style.

This half stack includes the Marshall 1959HW Handwired Plexi Amp Head and Marshall 1960AHW or 1960BHW 120W 4x12 Extension Cabinet.

Marshall 1959HW Handwired Plexi Amplifier Head
The 1959HW is a handwired reissue of a circa 1967 100W Superlead head. Since 1967 when the JMP (Jim Marshall Products) Plexi panels were introduced, the Superlead head has been the benchmark for all-tube distortion and tight crunch. Tube lineup includes 4 EL34s in the power section and 3 ECC83s in the preamp. True bypass effects loop, 3-band EQ, and presence control.

Marshall 1960AHW or 1960BHW 120W 4x12 Extension Cabinet
The Marshall 1960 AHW or 1960BHW Extension Speaker Cabinet is a hand-soldered, 120W, mono, 16-ohm 4x12" guitar speaker cabinet with salt 'n' pepper grille cloth, metal handles, loaded with reissue 30W Celestion G12H speakers.

Marshall 1959HW and 1960AHW or 1960BHW Half Stack Features:

• Marshall 1959HW Handwired Plexi Head
• Handwired reissue of 1967 Superlead
• 100W
• 4 EL34 power tubes
• 3 ECC83 preamp tubes
• True bypass effects loop
• 3-band EQ
• Presence control
  
  Marshall 1960AHW or 1960BHW 120W 4x12 Extension Cabinet
• Hand soldered
• 4x12" cabinet
• 120W
• Mono
• 16 ohm
• Salt 'n' pepper grille
• Metal handles
• Reissue 30W Celestion G12H speakers

Thirsty for more power and tube tone? Get the original quencher for a dry guitar tone. Order today.

A fire-breathing stack based on Jim Marshall's first amp!

This full stack includes one JTM45 amp head, one 1960AX angled guitar extension cab, and one 1960BX straight guitar extension cab.

Marshall JTM45 Amp Head
A lovingly created reproduction of Jim Marshall's first amplifier. Now the classic JTM45 amplifier head is accessible to all who enjoy its glassy, clean tone and fluid, warm sustain.


By including GZ34 valve rectification, as found in the original, Marshall has ensured a faithful recreation of the JTM45's glorious sound. The GZ34 rectifier valve interacts with the rest of the valves causing subtle harmonics to shift and smolder beneath every note you play.

Marshall 1960AX & 1960BX 100W 4x12 Guitar Extension Cabinets
Each speaker cab consists of 4 separate birch ply enclosures, each loaded with a Celestion G12M Greenback 12" speaker and has a 100W power handling rating. Tonally, these speaker cabinets fall between the 1960A's brightness and the 1960TV's warmth. Greenback G12M speakers have a very distinctive sound with a fast, snappy response that adds detail and dynamics to both clean and distorted playing. These cabinets use the early '70s LC checkered grille cloths and a less-textured vinyl covering.

Marshall JTM45, 1960AX and 1960BX Full Stack Specifications:

• Marshall JTM45 Amp Head
• Output (RMS): 30 watts
• Preamp valves: 3 x ECC83
• Power amp valves: 2 x 5881
• GZ34 valve rectifier
• 3-band EQ
• Presence control
• Dimensions: 26"W x 10-1/4"H x 8"D
• Weight: 32 lbs.
  
  

Marshall JTM45, 1960AX and 1960BX Full Stack Features:

• Marshall JTM45 Amp Head
• 30W head
• Clean tone
• Warm sustain
• Classic design
  
  Marshall 1960AX & 1960BX 100W 4x12 Guitar Extension Cabinets
• Four 12" Celestion Greenback G12M speakers
• each
• 100W handling
• Checkered grille cloths
• 100 lbs. each

Crave real British tube sound? Here's the rig that'll scratch your itch. Order today with the protection of our 45-day lowest price and total satisfaction guarantees!

Based on a direct descendant of the Plexi, its got trademark Marshall power and tone to spare!

This full stack includes one JCM800 2203 tube head, one 1960A angled guitar extension cab, and one 1960B straight guitar extension cab.

Marshall JCM800 2203 Vintage Series 100W Tube Head
One of the most highly respected 100W Marshall heads in the company's long history. Evolving from the legendary Plexi head, it was one of the first Marshall amplifiers to feature a master volume control. The essence of simplicity, the JCM800 is a one-channel, all-valve amp with no reverb or effects. Its easy control panel, distinctive roar, and larger-than-life edge immediately set the standard by which all other rock amps were judged and it remained the industry benchmark throughout the entire 16 years of its production life. Now it's back by popular demand and just like the 1959SLP and 1987X it has a Series Effects Loop with true bypass that takes the loop completely out of the circuit ensuring the original tone isn't compromised in any shape or form.

Marshall 1960A & 1960B 300W 4x12 Guitar Extension Cabinets
These speaker cabinets put out beautiful tone at any volume. The addition of an impedance (4- or 16-ohm) mono/stereo switching mechanism has transformed the "industry standard" 1960 into the ultimate speaker cab. These 280W Marshall cabs are loaded with Celestion Vintage speakers.

Marshall JCM800 2203X, 1960A, and 1960B Full Stack Specifications:

• Marshall JCM800 2203 Vintage Series 100W Tube Head
• 30"W x 9"H x 12"D
• 41 lbs.
  
  Marshall 1960A & 1960B 300W 4x12 Guitar Extension Cabinets
• Speaker Type: Celestion G12T-75W
• Speaker Configuration: 4x12"
• Power (RMS): 300W
• Selectable Mono/Stereo: Yes
• Impedance Stereo/Mono: 8 Ohm, 16/4 Ohm
• 30"W x 32-3/4"H x 14-1/4"D
• 82 lbs.

Marshall JCM800 2203X, 1960A, and 1960B Full Stack Features:

• Marshall JCM800 2203 Vintage Series 100W Tube Head
• 4 EL34s in the power stage
• 3 ECC83s in the preamp
• True bypass series FX loop
• 3-band EQ
• Presence control
  
  

Order today with the protection of our 45-day lowest price and total satisfaction guarantees!

Superb construction, sound, and features.

This Marshall full stack includes one JVM410H Tube Amp Head and a 1960A angled cab with a 1960B straight cab for some serious stage presence.

JVM410H Tube Amp Head
In a nutshell, the Marshall all-valve, 4-channel JVM410H 100-Watt tube head is the most versatile Marshall amplifier ever made. It also boasts more gain than any other Marshall to date-and that's really saying something!

Each of its 4 channels Clean, Crunch, OD1 & OD2 are not only completely independent of each other, they all boast 3 Modes, all 12 of which are footswitchable and feature their own unique gain structure. It makes the JVM 4-channel effectively 12 Marshalls in one!

The JVM410H amp head has studio-quality digital reverb with a level control for each channel. This is also footswitchable, as are the amp's two Master Volume controls and the Series/Parallel effects loop. Resonance and Presence are equipped with master controls.

Even though the head and combo both house 28 controls and 8 LED switches on their front panels, they're incredibly simple to understand because of the extremely logical layout. Each of the 4 channels has the usual suspects when it comes to controls Volume, Bass, Middle, Treble & Gain-accounting for 20 of the 28 controls right away. Take away the 4 reverb controls and you're only left with 4 Master controls-2 Master Volumes plus Resonance & Presence.

Add to this an ingenious footswitch (UK patent pending) and the fact all the amp's switching (channel/modes, Reverb, Master Volume selection, FX loop) can be done via MIDI and you're looking at an incredibly flexible amp! The 6-way footswitch boasts 7 LEDs and memory, plus it connects to the amp via a regular guitar cable.

From the cleanest clean to the filthiest distortion ever found in a Marshall and all points in-between, the JVM410H all-valve amp head will give you whatever tone you need right when you need it.

1960A and 1960B 300W 4x12 Guitar Extension Cabinet
The Marshall 1960 Speaker Cabinet puts out beautiful tone at any volume. The addition of an impedance (4 or 16 ohm) mono/stereo switching mechanism has transformed the "industry standard" 1960 into the ultimate speaker cab. These 280W Marshall cabs are loaded with Celestion Vintage speakers. The bottom cabinet is traditionally square-shaped with casters while the top speaker has an angled front.

Marshall JVM Series JVM410H, 1960A and 1960B Full Stack Specifications:

• 1960A and 1960B 300W 4x12 Guitar Extension Cabinet
• \Speaker Type: Celestion G12T-75W
• Speaker Configuration: 4 x12
• Power (RMS): 300W
• Selectable Mono/Stereo: Yes
• Impedance Stereo/Mono: 8 ohm, 16/4 ohm
• 30"W x 32-3/4"H x 14-1/4"D
• 82 lbs.

Marshall JVM Series JVM410H, 1960A and 1960B Full Stack Features:

• JVM410H Tube Amp Head
• 100-Watt valve head
• Valve complement: 5 x ECC83 (12AX7s) in preamp, 2 x EL34s in power amp
• 4 independent, footswitchable channels-Clean, Crunch, OD1 & OD2
• Each channel boasts 3 footswitchable modes Green, Orange & Red
• Studio quality, footswitchable digital reverb with level controls for all 4 channels.
• 2 footswitchable master volumes
• Two FX loops-Series/Parallel & Parallel
• Series/Parallel FX loop is footswitchable
• Emulated line out
• 6-way, 7-LED footswitch with memory capabilities (UK patent pending)
• All switching can be done via MIDI
• Made in England
  
  1960A or 1960B 300W 4x12 Guitar Extension Cabinets
• Bottom cabinet is square with caster wheels
• Top cabinet's front angles back and rests on on top of other cabinet.

Get a start on a super stack. Order today.

The sound that started it all.

1959SLPX Vintage Series 100W Tube Head

This all-tube Marshall 1959SLPX half-stack tone machine cranks out fabulous lead distortion and tight crunch exactly like the original model from the 1967 to 1969 era. This guitar amp head features 100W of power from 4 EL34s and 3 ECC83s in the preamp-the exact configuration of the original. True bypass series FX loop, 3-band EQ, and presence control.

1960AX and 1960BX 100W 4x12 Guitar Extension Cabinet

The Marshall 1960AX and 1960BX speaker cabs consist of 4 separate birch ply enclosures each. They are loaded with a Celestion G12M Greenback 12" speaker and have a 100W power handling rating. Tonally these speaker cabinets falls between the 1960AX's brightness and the 1960TV's warmth. Greenback G12M speakers have a very distinctive sound with a fast, snappy response that adds detail and dynamics to both clean and distorted playing. The 1960X Extension Cabinet uses the early '70s LC checkered grille cloth and a less-textured vinyl covering. A power brake is recommended. The 1960AX is an angled cab. The 1960BX is a straight cab.

Marshall 1959SLP and 1960AX or 1960BX Half Stack Features:

• Head:
• 100W
• 4 EL34s in the power stage
• 3 ECC83s in the preamp
• True bypass series FX loop
• 3-band EQ
• Presence control
  
  Cabinet:
• Four 12" Celestion Greenback G12M speakers
• 100W handling
• Checkered grille cloth
• Straight or angled front
• 100 lbs.

Order today and rule.

With Kerry King's signature sound section for punishing modern rock impact.

This full stack includes one JCM800 2203KK amp head, one 1960AV angled guitar extension cab, and one 1960BV straight guitar extension cab.

Marshall 2203KK Kerry King Signature JCM800 Guitar Amp Head
The all-valve Kerry King Signature JCM800 2203KK is the essence of simplicity-a single-channel tube amp with no reverb or effects. It's easy control panel, distinctive roar, and larger than life edge has set the standard by which many rock amps are judged.
This Kerry King model features a switchable Kerry King signature sound section called "The Beast" that has two adjustable controls-"Assault" & "Gate." "Assault" intensity controls the extent of Kerry's signature EQ boost, and "Gate" is an adjustable, studio-quality, ultra-fast noise reduction unit. You'll still find a Series Effects Loop with true bypass that takes the loop completely out of the circuit, ensuring the original tone isn't compromised in any shape or form. The 3-band EQ gives you plenty of control, but the base tone of this amplifier is patterned after the reverse-shape EQ setting used by Kerry himself! Eye-catching tribal graphics blaze from the front panel and baffle. Jim Marshall and Kerry King's signature's on the control panel identify its pedigree.

Marshall 1960AV & 1960BV 280W 4x12 Guitar Extension Cabinets
These speaker cabs put out beautiful tone at any volume. The addition of an impedance (4- or 16-ohm) mono/stereo switching mechanism has transformed the "industry standard" 1960 into the ultimate speaker cab. These 280W Marshall cabinets are loaded with Celestion Vintage 30 speakers.

Marshall JCM800 2203KK, 1960AV, and 1960BV Full Stack Specifications:

• Marshall 2203KK Kerry King Signature JCM800 Guitar Amp Head
• 30"W x 9"H x 12"D
• 41 lbs.
  
  Marshall 1960AV & 1960BV 280W 4x12 Guitar Extension Cabinets
• 280W handling
• 4 x 12" Celestion Vintage 30 speakers
• Impedance (4- or 16-ohm) and mono/stereo switching

Marshall JCM800 2203KK, 1960AV, and 1960BV Full Stack Features:

• Marshall 2203KK Kerry King Signature JCM800 Guitar Amp Head
• 100W valve head
• 4 KT88s in the power stage
• 3 ECC83s in the preamp
• Master Volume
• Preamp Volume
• Standby Switch
• True bypass series FX loop
• 3-band EQ
• Presence control
• "The Beast" Boost
• Gate Threshold
• Assault Intensity
• Jim Marshall and Kerry King signatures on control panel
• Made in England

Order today with the protection of our 45-day lowest price and total satisfaction guarantees!

Vintage rock tones with modern features and high levels of gain!

The Marshall Vintage Modern 2466 Full-Stack includes the Vintage Modern 2466 Tube Amp Head, Vintage Modern 425A angled speaker cabinet and Vintage Modern 425B straight speaker cab.

The Marshall Vintage Modern 2466 Tube Amp Head is an all-valve amplifier with a choice of two dynamic ranges selectable by footswitch. The Low range equates equates to the performance you would come to expect from a stock vintage Marshall amplifier in terms of tone and available gain. The High range adds an extra preamp valve into the signal path, facilitating those classic hard rock tones of the seventies. Add to this the ability to dynamically interface with your instrument's Volume and Tone controls and the experience translates into a truly expressive and organic feel in performance.

Two frequency selective Pre-amp Volumes (Gains) - Body and Detail - facilitate greater flexibility in tone shaping for individual guitars and styles while the power amplifier is heavily influenced by the first Marshall guitar amplifiers to be produced, with four KT66 output valves yielding that substantial, fat and smooth tone. A MID Boost switch on the front panel fattens the tone even more while a traditional Marshall tone control circuit enables fine tuning of your sound.

A master volume has been included in order to practically manage the output levels at all venues. This is implemented after the phase splitter in order to fully exploit maximum preamp drive when the master is turned down low. A reverb level control mixes the on board plate reverb with the direct signal to whatever degree the player chooses. The reverb can be toggled on and off via the footswitch.

Finally, a series FX loop is provided for those players who wish to use outboard effects to further enhance their sound. Loop levels of 10dB and +4dB can be controlled via a rear panel switch as well as the option to completely bypass this feature if it is not required.

The cosmetics are also a carefully crafted hybrid of old and new styles made even more dramatic by the deep purple vinyl that covers the entire speaker series.

The Marshall Vintage Modern 425A angled cab and 425B straight cab are traditional Marshall 4 x 12 speaker enclosures in design. These cabs are mono/stereo switchable and are loaded with G12C 25 Watt Celestion Greenbacks. These were specifically developed for the Limited Edition Jimi Hendrix Super100JH stack and are voiced to give that rich and balanced harmonic timbre that complements vintage tone and the Vintage Modern Series perfectly.

The cosmetics are also a carefully crafted hybrid of old and new styles made even more dramatic by the deep purple vinyl that covers the entire series.

Marshall 2466, 425A, and 425B Full Stack Specifications:

• Head Dimensions: 29-1/2" x 12" x 9" (750 x 310 x 230 mm)
• Weight: 49.6 lbs (22.5 kg)
  
  Cabinet
• Impedance
• Mono 16 Ohms/4 Ohms
• Stereo 8 Ohms/8 Ohms
• Dimensions 30.5" x 30" x 14.5" (770 x 755 x 365 mm)
• Weight
• 425A: 79 lbs. (36 kg)
• 425B: 81.5 lbs (37 kg)

Marshall 2466, 425A, and 425B Full Stack Features:

• 100-Watt valve head
• Valve compliment: 4 x ECC83 (12AX7s) in preamp, 4 x KT66 in power amp
• Master Volume with two Gain Controls Detail (highs) & Body (lows)
• Two footswitchable Dynamic Ranges Low & High
• Mid Boost switch
• Footswitchable Proprietary digital Plate Reverb
• Series FX loop with level switch and bypass
• Made in England
  
  100-Watt, 4x12" cabinet
• Angled front
• Loaded with Celestion G12C 25 Greenbacks
• Mono or Stereo switchable
• 16 Ohms/4 Ohms mono
• 8 Ohms stereo
• Birch ply construction
• "finger-locking" joints
• Made in England

Few word combinations are as exciting as "Marshall stack"! Make it yours. Order today.

A rig that'll play the hard-edged modern sound that made Kerry King a master of metal.

This full stack includes one JCM800 2203KK amp head, one 1960A angled guitar extension cab, and one 1960B straight guitar extension cab.

Marshall 2203KK Kerry King Signature JCM800 Guitar Amp Head
The all-valve Kerry King Signature JCM800 2203KK is the essence of simplicity-a single-channel tube amp with no reverb or effects. It's easy control panel, distinctive roar, and larger than life edge has set the standard by which many rock amps are judged.
This Kerry King model features a switchable Kerry King signature sound section called "The Beast" that has two adjustable controls-"Assault" & "Gate." "Assault" intensity controls the extent of Kerry's signature EQ boost, and "Gate" is an adjustable, studio-quality, ultra-fast noise reduction unit. You'll still find a Series Effects Loop with true bypass that takes the loop completely out of the circuit, ensuring the original tone isn't compromised in any shape or form. The 3-band EQ gives you plenty of control, but the base tone of this amplifier is patterned after the reverse-shape EQ setting used by Kerry himself! Eye-catching tribal graphics blaze from the front panel and baffle. Jim Marshall and Kerry King's signature's on the control panel identify its pedigree.

Marshall 1960A & 1960B 300W 4x12 Guitar Extension Cabinets
These speaker cabs put out beautiful tone at any volume. The addition of an impedance (4- or 16-ohm) mono/stereo switching mechanism has transformed the "industry standard" 1960 into the ultimate speaker cab. These 280W Marshall cabs are loaded with Celestion Vintage speakers.

Marshall JCM800 2203KK, 1960A, and 1960B Full Stack Specifications:

• Marshall 2203KK Kerry King Signature JCM800 Guitar Amp Head
• 30"W x 9"H x 12"D
• 41 lbs.
  
  Marshall 1960A & 1960B 300W 4x12 Guitar Extension Cabinets
• Speaker Type: Celestion G12T-75W
• Speaker Configuration: 4"x12"
• Power (RMS): 300W
• Selectable Mono/Stereo: Yes
• Impedance Stereo/Mono: 8 Ohm, 16/4 Ohm
• 30"W x 32-3/4"H x 14-1/4"D
• 82 lbs.

Marshall JCM800 2203KK, 1960A, and 1960B Full Stack Features:

• Marshall 2203KK Kerry King Signature JCM800 Guitar Amp Head
• 100W valve head
• 4 KT88s in the power stage
• 3 ECC83s in the preamp
• Master Volume
• Preamp Volume
• Standby Switch
• True bypass series FX loop
• 3-band EQ
• Presence control
• "The Beast" Boost
• Gate Threshold
• Assault Intensity
• Jim Marshall and Kerry King signatures on control panel
• Made in England

Order today with the protection of our 45-day lowest price and total satisfaction guarantees!

A super-versatile rig featuring the Marshall Vintage Modern 2266 Tube Amp Head!

This Marshall full stack includes one 2266 amp head, one 425A angled speaker cab, and one 425B straight speaker cab.

Marshall Vintage Modern 2266 Tube Amp Head
This head is an all-valve single channel amplifier with a choice of two dynamic ranges selectable by footswitch. The Low range equates to the performance you would come to expect from a stock vintage Marshall amplifier in terms of tone and available gain. The High range adds an extra preamp valve into the signal path, facilitating those classic hard rock tones of the seventies. Add to this the ability to dynamically interface with your instrument's Volume and Tone controls and the experience translates into a truly expressive and organic feel in performance.
Two frequency selective Pre-amp Volumes (Gains)-Body and Detail-facilitate greater flexibility in tone shaping for individual guitars and styles while the power amplifier is heavily influenced by the first Marshall amplifiers to be produced, with two KT66 output valves yielding that substantial, fat and smooth tone. A MID Boost switch on the front panel fattens the tone even more while a traditional Marshall tone control circuit enables fine tuning of your sound.
A master volume has been included in order to practically manage the output levels at all venues. This is implemented after the phase splitter in order to fully exploit maximum preamp drive when the master is turned down low. A reverb level control mixes the on board plate reverb with the direct signal to whatever degree the player chooses. The reverb can be toggled on and off via the footswitch.
Finally, a series FX loop is provided for those players who wish to use outboard effect to further enhance their sound. Loop levels of 10dB and +4dB can be controlled via a rear panel switch as well as the option to completely bypass this feature if it is not required.
The cosmetics are also a carefully crafted hybrid of old and new styles-made even more dramatic by the deep purple vinyl that covers the entire series.

Marshall Vintage Modern 425A & 425B 4x12 Extension Speaker Cabinets
These cabinets are traditional Marshall 4 x 12 speaker cabs in design. These cabs are mono/stereo switchable and are loaded with G12C 25 Watt Celestion Greenbacks. These were specifically developed for the Limited Edition Jimi Hendrix Super100JH stack and are voiced to give that rich and balanced harmonic timbre that complements vintage tone and the Vintage Modern Series perfectly.
The cosmetics are also a carefully crafted hybrid of old and new styles-made even more dramatic by the deep purple vinyl that covers the entire series.

Marshall Vintage Modern 2266, 425A and 425B Full Stack Specifications:

• Marshall Vintage Modern 2266 Tube Amp Head
• Dimensions: 29-1/2" x 12" x 9" (750 x 310 x 230mm)
• Weight: 39.6 lbs. (18 kg)
  
  Marshall Vintage Modern 425A & 425B 4x12 Extension Speaker Cabinets
• Dimensions: 30.5" x 30" x 14.5" (770 x 755 x 365mm)
• 425A weight: 79 lbs. (36 kg)
• 425B weight: 81.5 lbs. (37 kg)

Marshall Vintage Modern 2266, 425A and 425B Full Stack Features:

• Marshall Vintage Modern 2266 Tube Amp Head
• 50-watt valve head
• Valve compliment: 4 x ECC83 (12AX7s) in preamp, 2 x KT66 in power amp
• Master Volume with two Gain Controls-Detail (highs) & Body (lows)
• Two footswitchable Dynamic Ranges Low & High
• Mid Boost switch
• Footswitchable Proprietary digital Plate Reverb
• Series FX loop with level switch and bypass
• Made in England
  
  Marshall Vintage Modern 425A & 425B 4x12 Extension Speaker Cabinets
• 100-watt cabinets
• Loaded with Celestion G12C 25 Greenbacks
• Mono or Stereo switchable
• 16 ohms/4 ohms mono
• 8 ohms stereo
• Birch ply construction
• "finger-locking" joints
• Made in England

Make an investment in your sound that will pay dividends for years to come. Order now with the protection of our 45-day lowest price and total satisfaction guarantees

Inspired by Pete Townshend's quest for power, this is a half-stack for heavy hitters.

Marshall 1959SLPX Vintage Series 100W Tube Head
This all-tube tone machine cranks out fabulous lead distortion and tight crunch exactly like the original model from the 1967 to 1969 era. Inspired by Pete Townshend's unquenchable thirst for volume, this guitar amp head features 100W of power from 4 EL34s and 3 ECC83s in the preamp-the exact configuration of the original. True bypass series FX loop, 3-band EQ, and presence control.

Marshall 1960TV Cabinet
The 1960TV speaker cab has an angled front; four 12" Greenback speakers; and a warmer, thicker sound than the 1960A. This 100W, mono, 16-ohm cabinet is 3 inches taller than a standard 1960A 4x12 cabinet which results in well defined mid range and a lowered resonant frequency for more prominent lows. The 25W Greenbacks are less in your face than the 75W Celestions in the 1960A. Although not a reissue-it was never offered in the past-this cab recreates the classic look and tones of yesteryear.

Marshall 1959SLPX and 1960TV Half Stack Specifications:

• Marshall 1960TV Cabinet
• Handles 100W
• 16 ohms
• 29-3/5"W x 35-1/2"H x 14-4/5"D
• 97 lbs.

Marshall 1959SLPX and 1960TV Half Stack Features:

• Marshall 1959SLPX Vintage Series 100W Tube Head
• 4 EL34s in the power stage
• 3 ECC83s in the preamp
• True bypass series FX loop
• 3-band EQ
• Presence control
  
  Marshall 1960TV Cabinet
• Angled front
• Four 12" 25W Greenback speakers for warmer, thicker sound than the 1960A
• Original grille cloth
• 3" taller than standard 4x12 cabs

Order today with the protection of our 45-day lowest price and total satisfaction guarantees!

A rock standard now with impedance switching!

If you want to keep it simple, this half stack kit which includes the JCM800 2203 Vintage Series 100W Tube Head and 1960AV or 1960BV 280W 4X12 Guitar Extension Cabinet is the kit to get you going.

JCM800 2203 Vintage Series 100W Tube Head
The all-valve JCM800 2203 is one of the most highly respected 100W Marshall heads in the company's long history. Evolving from the legendary Plexi head, it was one of the first Marshall amps to feature a master volume control. The essence of simplicity, the JCM800 is a one-channel, all-valve amp with no reverb or effects. Its easy control panel, distinctive roar, and larger-than-life edge immediately set the standard by which all other rock amps were judged and it remained the industry benchmark throughout the entire 16 years of its production life. Now it's back by popular demand and features a Series Effects Loop with true bypass that takes the loop completely out of the circuit ensuring the original tone isn't compromised in any shape or form.

1960AV or 1960BV 280W 4x12 Guitar Extension Cabinet
The Marshall 1960V Vintage Speaker Cabinet puts out beautiful tone at any volume. The addition of an impedance (4 or 16 ohm) mono/stereo switching mechanism has transformed the "industry standard" 1960 into the ultimate speaker cab. This 280W Marshall cab is loaded with Celestion Vintage 30 speakers.

Marshall JCM800 2203X and 1960AV or 1960BV Half Stack Specifications:

• JCM800 2203 Vintage Series 100W Tube Head
• 100W
• 30"W x 9"H x 12"D
• 41 lbs.
  
  1960AV or 1960BV 280W 4x12 Guitar Extension Cabinet
• 280W handling
• Impedance (4 or 16 ohm) with Mono/Stereo switching

Marshall JCM800 2203X and 1960AV or 1960BV Half Stack Features:

• JCM800 2203 Vintage Series 100W Tube Head
• 4 EL34s in the power stage
• 3 ECC83s in the preamp
• True bypass series FX loop
• 3-band EQ
• Presence control
  
  1960AV or 1960BV 280W 4x12 Guitar Extension Cabinet
• 4 x 12 Celestion Vintage 30 speakers

No backline would be complete without the legendary Marshall 4x12 cab. Order now.

More channels, more gain, more versatility.

This half stack includes the Marshall JVM410H Tube Amp Head and 1960V Vintage Speaker Cabinet.

JVM410H Tube Amp Head
In a nutshell, the Marshall all-valve, 4-channel JVM410H 100-Watt tube head is the most versatile Marshall amplifier ever made. It also boasts more gain than any other Marshall to date and that's really saying something!

Each of its 4 channels Clean, Crunch, OD1 & OD2 are not only completely independent of each other, they all boast 3 Modes, all 12 of which are footswitchable and feature their own unique gain structure. It makes the JVM 4-channel effectively 12 Marshalls in one!

The JVM410H amp head has studio-quality digital reverb with a level control for each channel. This is also footswitchable, as are the amp's two Master Volume controls and the Series/Parallel effects loop. Resonance and Presence are equipped with master controls.

Even though the head and combo both house 28 controls and 8 LED switches on their front panels, they're incredibly simple to understand because of the extremely logical layout. Each of the 4 channels has the usual suspects when it comes to controls Volume, Bass, Middle, Treble & Gain accounting for 20 of the 28 controls right away. Take away the 4 reverb controls and you're only left with 4 Master controls 2 Master Volumes plus Resonance & Presence.

Add to this an ingenious footswitch (UK patent pending) and the fact all the amp's switching (channel/modes, Reverb, Master Volume selection, FX loop) can be done via MIDI and you're looking at an incredibly flexible amp! The 6-way footswitch boasts 7 LEDs and memory, plus it connects to the amp via a regular guitar cable.

From the cleanest clean to the filthiest distortion ever found in a Marshall and all points in-between, the JVM410H all-valve amp head will give you whatever tone you need right when you need it.

1960V Vintage Speaker Cabinet
The Marshall 1960V Vintage Speaker Cabinet puts out beautiful tone at any volume. The addition of an impedance (4 or 16 ohm) mono/stereo switching mechanism has transformed the "industry standard" 1960 into the ultimate speaker cab. This 280W Marshall cab is loaded with Celestion Vintage 30 speakers.

Marshall JVM Series JVM410H and 1960AV or 1960BV Half Stack Features:

• JVM410H Tube Amp Head
• 
  
• 100-Watt valve head
• Valve complement: 5 x ECC83 (12AX7s) in preamp, 2 x EL34s in power amp
• 4 independent, footswitchable channels Clean, Crunch, OD1 & OD2
• Each channel boasts 3 footswitchable modes Green, Orange & Red
• Studio quality, footswitchable digital reverb with level controls for all 4 channels.
• 2 footswitchable master volumes
• Two FX loops Series/Parallel & Parallel
• Series/Parallel FX loop is footswitchable
• Emulated line out
• 6-way, 7-LED footswitch with memory capabilities (UK patent pending)
• All switching can be done via MIDI
• Made in England
  
  1960V Vintage Speaker Cabinet
  
• 280W handling
• 4 - 12" Celestion Vintage 30 speakers
• Impedance (4 or 16 ohm) and mono/stereo switching

No backline would be complete without the legendary Marshall head and 4x12 cab. Order now.

JVM410H Tube Amp Head

In a nutshell, the Marshall all-valve, 4-channel JVM410H 100-watt tube head is the most versatile Marshall amplifier ever made. It also boasts more gain than any other Marshall guitar amp head to date-and that's really saying something.

Each of its 4 channels-Clean, Crunch, OD1 & OD2-are not only completely independent of each other, they all boast 3 modes, all 12 of which are footswitchable and feature their own unique gain structure. It makes the JVM 4-channel effectively 12 Marshalls in one.

The JVM410H amp head has studio-quality digital reverb with a level control for each channel. This is also footswitchable, as are the amp's two Master Volume controls and the Series/Parallel effects loop. Resonance and Presence are equipped with master controls.

Even though the head and combo both house 28 controls and 8 LED switches on their front panels, they're incredibly simple to understand because of the extremely logical layout. Each of the 4 channels has the usual suspects when it comes to control-Volume, Bass, Middle, Treble & Gain-accounting for 20 of the 28 controls right away. Take away the 4 reverb controls and you're only left with 4 Master controls-2 Master Volumes plus Resonance & Presence.

Add to this an ingenious footswitch (UK patent pending) and the fact all the amplifier's switching (channel/modes, Reverb, Master Volume selection, FX loop) can be done via MIDI and you're looking at an incredibly flexible amp! The 6-way footswitch boasts 7 LEDs and memory, plus it connects to the amp via a regular guitar cable.

From the cleanest clean to the filthiest distortion ever found in a Marshall and all points in-between, the JVM410H all-valve guitar amp head will give you whatever tone you need right when you need it.

1960A and 1960B 300W 4x12 Guitar Extension Cabinet

The Marshall 1960 Speaker Cabinet puts out beautiful tone at any volume. The addition of an impedance (4 or 16 ohm) mono/stereo switching mechanism has transformed the "industry standard" 1960 into the ultimate speaker cab. These 300W Marshall speaker cabinets are loaded with Celestion Vintage speakers. The 1960A cab is angled. The 1960B cab is straight.

Marshall JVM Series JVM410H and 1960A or 1960B Half Stack Features:

• Head:
• 100-watt valve head
• Valve complement: 5 x ECC83 (12AX7s) in preamp, 2 x EL34s in power amp
• 4 independent, footswitchable channels Clean, Crunch, OD1 & OD2
• Each channel boasts 3 footswitchable modes Green, Orange & Red
• Studio quality, footswitchable digital reverb with level controls for all 4 channels.
• 2 footswitchable master volumes
• Two FX loops Series/Parallel & Parallel
• Series/Parallel FX loop is footswitchable
• Emulated line out
• 6-way, 7-LED footswitch with memory capabilities (UK patent pending)
• All switching can be done via MIDI
• Made in England
  
  Cabinet:
• Speaker type: Celestion G12T-75W
• Speaker configuration: 4x12"
• Power (RMS): 300W
• Selectable mono/stereo: Yes
• Impedance stereo/mono: 8 Ohm, 16/4 Ohm
• 30"W x 32-3/4"H x 14-1/4"D
• 82 lbs.

Save BIG when you buy today!

Real all-tube vintage flavor from the original maker.

This half stack includes the Marshall 1987XL Vintage Series 50W Tube Head and Marshall 1960AX or 1960BX 100W 4x12 Guitar Extension Cabinet.

1987XL Vintage Series 50W Tube Head
The Marshall 1987XL Vintage Series 50W Tube Head gives you all the fabulous tube tone of the original 1987X from the 1966 to 1969 era plus a true bypass series FX loop. 3 ECC83 tubes in the preamp and 2 EL34s in the power section dish out that delicious, nasty overdrive behind Hendrix, Townshend, and scores of other greats. 3-band EQ and presence controls provide all the tweakage necessary to get the most out of this classic screamer. 50W. 26"W x 8"H x 10"D. 34 lbs.

Marshall 1960X 100W 4x12 Guitar Extension Cabinet
The Marshall 1960X cab consists of 4 separate birch ply speaker enclosures, each loaded with a Celestion G12M Greenback 12" speaker and has a 100W power handling rating. Tonally this speaker cabinet falls between the 1960A's brightness and the 1960TV's warmth. Greenback G12M speakers have a very distinctive sound with a fast, snappy response that adds detail and dynamics to both clean and distorted playing. The 1960X Extension Cabinet uses the early '70s LC checkered grille cloth and a less-textured vinyl covering. If used as a half stack with a 100W head, a power brake is recommended.

Marshall 1987XL and 1960AX or 1960BX Half Stack Features:

• 1987XL Vintage Series 50W Tube Head
• 50W of classic all-tube power
• 3 ECC83 tubes in the preamp
• 2 EL34s in the power section
• 3-band EQ
• Presence control
  
  Marshall 1960X 100W 4x12 Guitar Extension Cabinet
• 4 - 12" Celestion Greenback G12M speakers
• 100W handling
• Checkered grille cloth
• Straight or Angled front
• 100 lbs

To get the real sound, go for the real deal. Order today!

Original Marshall roar.

The 1959HW is a handwired reissue of a circa 1967 100W Superlead head. Since 1967 when the JMP (Jim Marshall Products) Plexi panels were introduced, the Superlead head has been the benchmark for all-tube distortion and tight crunch. Tube lineup includes 4 EL34s in the power section and 3 ECC83s in the preamp. True bypass effects loop, 3-band EQ, and presence control.

Marshall 1959HW Handwired Plexi Head Features:

• Handwired reissue of 1967 Superlead
• 100W
• 4 EL34 power tubes
• 3 ECC83 preamp tubes
• True bypass effects loop
• 3-band EQ
• Presence control

Thirsty for more power and tube tone? Get the original quencher for a dry guitar tone. Order today.

Randy Rhoads tribute amp.

This all-tube tone machine cranks out fabulous lead distortion and tight crunch exactly like the original model from the 1967 to 1969 era. Inspired by Randy Rhoads, this guitar amp head features 100W of power from 4 EL34s and 3 ECC83s in the preamp-the exact configuration of the original. True bypass series FX loop, 3-band EQ, and presence control. Covered in white, just like Randy liked them.

Throughout their history, Marshall has built strong relationships with the artists who fly the flag for Marshall. Sometimes, sadly, this partnership is ended prematurely. Cited by countless guitarists over the years, Randy Rhoads remains hugely influential in the world of rock 'n' roll and continues to inspire new generations to pick up a guitar. As a rock icon whose reputation as a technical wizard with a unique sense of style precedes him, Marshall felt it appropriate to honor this ambassador of Marshall with his own signature amp. Presenting the 1959RR head.

Marshall Super Lead 1959RR Limited Edition Randy Rhoads Tribute 100W Tube Guitar Amp Head Specifications:

• Dimensions: 29.1" x 10.63" x 8.27" (740 x 270 x 210mm)
• Weight: 47.2 lbs (21.4 kg)

Marshall Super Lead 1959RR Limited Edition Randy Rhoads Tribute 100W Tube Guitar Amp Head Features:

• Output: (RMS): 100 Watt
• 2 channels
• 2 volumes for each channel
• 3-band EQ
• Presence knob
• Cascade Mod
• Pre-Amp Valves: 3 x ECC83
• Power Amp Valves: 4 x EL34
• Birch ply cabinet

Buy your ticket for the Crazy Train. Call or click today to order.