The Groove Tubes SAG-MHG Marshall High Gain Kit contains 2 SAG ECC83S and 1 AX7-MPI tubes optimized for the preamp stage of Marshall-style amplifiers.

Specially selected from premium Groove Tubes preamp tubes which have been tested to meet the GT standard. Special Applications Group (SAG) provides further testing and grading of vacuum tubes for certain performance characteristics.

This 3-tube set is optimized for your Marshall, Bogner, Rivera, Mesa or British type amps which use (or will benefit from) the ECC83 (12AX7) preamp tubes. SAG-MHG includes two high output preamp tubes to be used in the V1 and V2 positions, and one MPI (matched phase inverter) tube for the V3 position. The matched phase inverter may be a 12AX7 or an ECC83, as it will be matched for its response curves with the other two tubes. The phase inverter is not part of the tine generation stage, it is a current driver.

The V1 and V2 tubes will increase the front end output structure of amplifiers from about 10% to as much as 25% or more over typical stock tubes.

The V3, matched phase inverter tube will assure a balanced output section when used with matched power tubes (highly recommended) which will assure sustain across the entire range of your instrument.

The MPI (Matched Phase Inverter) is a SAG selected 12AX7 or ECC83, as this tube is not part of the tone generation stage, but part of the output section and is chosen for its current drive and rise time characteristics.

Use this MPI in any application where a phase inverter / driver of the ECC83/12AX7/7025 tube is specified. The phase inverter / driver position of a guitar or bass amp is a current driving position, and not part of the tone generation stage. These tubes are selected for specific characteristics, so may be a 12AX7R, 12AX7C, 12AX7M or another 12AX7 type that has been selected for specific curve traces as the objective. This tube cannot be specified as to type in the kit.

These kits also work particularly well in Fender Blackface and Silverface amps where the increased gain and current out of the first gain stage combined with a switch from the 12AT7 in the phase inverter to a 12AX7 will yield a much more aggressive tone. These amps which are normally considered to be on the "clean" side will become more aggressive with this kit.

Save BIG when you buy today!

Explore the story of rock's greatest amp maker!

Marshall amps have defined the sound of a generation of rock, Used by Jimi Hendrix, Eric Clapton, Jeff Beck, Ritchie Blackmore, Jimmy Page, and thousands more. This book explores the British company responsible for the amp stack and that sweet overdrive sound.

Michael Doyle (the acknowledged authority on the subject) traces the impressive lineage of the British company and its guitar amps. The book is dotted with the names of rock luminaries and peppered with photos — over 100 in black-and-white plus a 32-page color section and a 32-page full-color appendix that reproduces all of the Marshall catalogues of the '60s.

Hal Leonard The History of Marshall Features:

• 256 pages
• Over 100 black-and-white pictures
• 32-page color section and 32-page appendix with reproductions of '60s Marshall catalogs

Order now and learn everything about the famous amp riding the top of your stack!

Marshall roar - 1967 style.

This half stack includes the Marshall 1959HW Handwired Plexi Amp Head and Marshall 1960AHW or 1960BHW 120W 4x12 Extension Cabinet.

Marshall 1959HW Handwired Plexi Amplifier Head
The 1959HW is a handwired reissue of a circa 1967 100W Superlead head. Since 1967 when the JMP (Jim Marshall Products) Plexi panels were introduced, the Superlead head has been the benchmark for all-tube distortion and tight crunch. Tube lineup includes 4 EL34s in the power section and 3 ECC83s in the preamp. True bypass effects loop, 3-band EQ, and presence control.

Marshall 1960AHW or 1960BHW 120W 4x12 Extension Cabinet
The Marshall 1960 AHW or 1960BHW Extension Speaker Cabinet is a hand-soldered, 120W, mono, 16-ohm 4x12" guitar speaker cabinet with salt 'n' pepper grille cloth, metal handles, loaded with reissue 30W Celestion G12H speakers.

Marshall 1959HW and 1960AHW or 1960BHW Half Stack Features:

• Marshall 1959HW Handwired Plexi Head
• Handwired reissue of 1967 Superlead
• 100W
• 4 EL34 power tubes
• 3 ECC83 preamp tubes
• True bypass effects loop
• 3-band EQ
• Presence control
  
  Marshall 1960AHW or 1960BHW 120W 4x12 Extension Cabinet
• Hand soldered
• 4x12" cabinet
• 120W
• Mono
• 16 ohm
• Salt 'n' pepper grille
• Metal handles
• Reissue 30W Celestion G12H speakers

Thirsty for more power and tube tone? Get the original quencher for a dry guitar tone. Order today.

Original Marshall roar.

The 1959HW is a handwired reissue of a circa 1967 100W Superlead head. Since 1967 when the JMP (Jim Marshall Products) Plexi panels were introduced, the Superlead head has been the benchmark for all-tube distortion and tight crunch. Tube lineup includes 4 EL34s in the power section and 3 ECC83s in the preamp. True bypass effects loop, 3-band EQ, and presence control.

Marshall 1959HW Handwired Plexi Head Features:

• Handwired reissue of 1967 Superlead
• 100W
• 4 EL34 power tubes
• 3 ECC83 preamp tubes
• True bypass effects loop
• 3-band EQ
• Presence control

Thirsty for more power and tube tone? Get the original quencher for a dry guitar tone. Order today.

The sound that started it all.

1959SLPX Vintage Series 100W Tube Head

This all-tube Marshall 1959SLPX half-stack tone machine cranks out fabulous lead distortion and tight crunch exactly like the original model from the 1967 to 1969 era. This guitar amp head features 100W of power from 4 EL34s and 3 ECC83s in the preamp-the exact configuration of the original. True bypass series FX loop, 3-band EQ, and presence control.

1960AX and 1960BX 100W 4x12 Guitar Extension Cabinet

The Marshall 1960AX and 1960BX speaker cabs consist of 4 separate birch ply enclosures each. They are loaded with a Celestion G12M Greenback 12" speaker and have a 100W power handling rating. Tonally these speaker cabinets falls between the 1960AX's brightness and the 1960TV's warmth. Greenback G12M speakers have a very distinctive sound with a fast, snappy response that adds detail and dynamics to both clean and distorted playing. The 1960X Extension Cabinet uses the early '70s LC checkered grille cloth and a less-textured vinyl covering. A power brake is recommended. The 1960AX is an angled cab. The 1960BX is a straight cab.

Marshall 1959SLP and 1960AX or 1960BX Half Stack Features:

• Head:
• 100W
• 4 EL34s in the power stage
• 3 ECC83s in the preamp
• True bypass series FX loop
• 3-band EQ
• Presence control
  
  Cabinet:
• Four 12" Celestion Greenback G12M speakers
• 100W handling
• Checkered grille cloth
• Straight or angled front
• 100 lbs.

Order today and rule.

The real screamin' deal!

This Marshall Full Stack includes a 1959SLPX Vintage Series 100W Tube Head and 1960AX/1960BX 100W 4x12 Guitar Extension Cabinets that enable you to play it loud and play it proud.

1959SLPX Vintage Series 100W Tube Head
This all-tube Marshall 1959SLPX tone machine cranks out fabulous lead distortion and tight crunch exactly like the original model from the 1967 to 1969 era. Inspired by Pete Townshend's unquenchable thirst for VOLUME, this guitar amp head features 100W of power from 4 EL34s and 3 ECC83s in the preamp the exact configuration of the original. True bypass series FX loop, 3-band EQ, and presence control.

1960AX and 1960BX 100W 4x12 Guitar Extension Cabinet
The Marshall 1960X speaker cab consists of 4 separate birch ply enclosures, each loaded with a Celestion G12M Greenback 12" speaker and has a 100W power handling rating. Tonally this speaker cabinet falls between the 1960A's brightness and the 1960TV's warmth. Greenback G12M speakers have a very distinctive sound with a fast, snappy response that adds detail and dynamics to both clean and distorted playing. The 1960X Extension Cabinet uses the early '70s LC checkered grille cloth and a less-textured vinyl covering. If used as a half stack with a 100W head, a power brake is recommended.

Marshall 1959SLP, 1960AX and 1960BX Full Stack Features:

• 1959SLPX Vintage Series 100W Tube Head
• 100W
• 4 EL34s in the power stage
• 3 ECC83s in the preamp
• True bypass series FX loop
• 3-band EQ
• Presence control
  
  1960AX and 1960BX 100W 4x12 Guitar Extension Cabinet
• 4 x 12 Celestion Greenback G12M speakers
• 100W handling
• Checkered grille cloth
• Straight or Angled front
• 100 lbs

This is the original head-cutting head. Make it yours and make history.

Inspired by Pete Townshend's quest for power, this is a half-stack for heavy hitters.

Marshall 1959SLPX Vintage Series 100W Tube Head
This all-tube tone machine cranks out fabulous lead distortion and tight crunch exactly like the original model from the 1967 to 1969 era. Inspired by Pete Townshend's unquenchable thirst for volume, this guitar amp head features 100W of power from 4 EL34s and 3 ECC83s in the preamp-the exact configuration of the original. True bypass series FX loop, 3-band EQ, and presence control.

Marshall 1960TV Cabinet
The 1960TV speaker cab has an angled front; four 12" Greenback speakers; and a warmer, thicker sound than the 1960A. This 100W, mono, 16-ohm cabinet is 3 inches taller than a standard 1960A 4x12 cabinet which results in well defined mid range and a lowered resonant frequency for more prominent lows. The 25W Greenbacks are less in your face than the 75W Celestions in the 1960A. Although not a reissue-it was never offered in the past-this cab recreates the classic look and tones of yesteryear.

Marshall 1959SLPX and 1960TV Half Stack Specifications:

• Marshall 1960TV Cabinet
• Handles 100W
• 16 ohms
• 29-3/5"W x 35-1/2"H x 14-4/5"D
• 97 lbs.

Marshall 1959SLPX and 1960TV Half Stack Features:

• Marshall 1959SLPX Vintage Series 100W Tube Head
• 4 EL34s in the power stage
• 3 ECC83s in the preamp
• True bypass series FX loop
• 3-band EQ
• Presence control
  
  Marshall 1960TV Cabinet
• Angled front
• Four 12" 25W Greenback speakers for warmer, thicker sound than the 1960A
• Original grille cloth
• 3" taller than standard 4x12 cabs

Order today with the protection of our 45-day lowest price and total satisfaction guarantees!

Superb construction, sound, and features.

The Marshall 1960 Speaker Cabinet puts out beautiful tone at any volume. The addition of an impedance (4 or 16 ohm) mono/stereo switching mechanism has transformed the "industry standard" 1960 into the ultimate speaker cab. These 280W Marshall cabs are loaded with Celestion Vintage speakers.

Marshall 1960A or 1960B 300W 4x12 Guitar Extension Cabinet Specifications:

• Speaker Type: Celestion G12T-75W
• Speaker Configuration: 4 x12
• Power (RMS): 300W
• Selectable Mono/Stereo: Yes
• Impedance Stereo/Mono: 8 ohm, 16/4 ohm
• 30"W x 32-3/4"H x 14-1/4"D
• 82 lbs.

Get a start on a super stack. Order today.

A rock standard now with impedance switching!

The Marshall 1960V Vintage Speaker Cabinet puts out beautiful tone at any volume. The addition of an impedance (4 or 16 ohm) mono/stereo switching mechanism has transformed the "industry standard" 1960 into the ultimate speaker cab. This 280W Marshall cab is loaded with Celestion Vintage 30 speakers.

Marshall 1960AV or 1960BV 280W 4x12 Guitar Extension Cabinet Specifications:

• 280W handling
• 4 x 12" Celestion Vintage 30 speakers
• Impedance (4 or 16 ohm) And mono/stereo switching

No backline would be complete without the legendary Marshall 4x12 cab. Order now.

The sound that launched the British blues invasion.

The Marshall 1962 Bluesbreaker Combo Amp is just like the one used by Eric Clapton during his stint with Mayall's Bluesbreakers and famously on the Beano sessions. With 30W output and 2x12 speakers, it produces a gutsy bass and vibrant top, coupled with an overall natural warmth. The valve rectification output stage, pioneered by Marshall in the early 1960s, is responsible for helping achieve the famed compression and sustain exhibited uniquely by both the JTM45 and 1962. Though somewhat tonally similar to a JTM45, the 1962 combo is loaded with 2 Celestion Greenback 25W speakers and also comes with a footswitchable tremolo effect.

If you're looking for that sensuous, creamy early Clapton sound, we guarantee that you'll find it in this beautifully reissued Marshall combo. The natural tone and overdrive of the 1962 Bluesbreaker Amp will quickly become a fundamental ingredient in your overall sound.

Marshall 1962 Bluesbreaker Combo Amp Specifications:

• 29-1/4"W x 23-3/4"H x 10-1/2"D (740 x 600 x 265mm)
• 66.6 lbs. (30.2kg)

Marshall 1962 Bluesbreaker Combo Amp Features:

• 30W output
• 2 - 12" 25W Celestion Greenback speakers
• Valve rectifier
• Footswitchable tremolo effect

Looking for authentic British blues tones? Put it in the cart!

The sound that launched the British blues invasion.

The Marshall 1962 Bluesbreaker Combo Amp is just like the one used by Eric Clapton during his stint with Mayall's Bluesbreakers and famously on the Beano sessions. With 30W output and 2x12 speakers, it produces a gutsy bass and vibrant top, coupled with an overall natural warmth. The valve rectification output stage, pioneered by Marshall in the early 1960s, is responsible for helping achieve the famed compression and sustain exhibited uniquely by both the JTM45 and 1962. Though somewhat tonally similar to a JTM45, the 1962 combo is loaded with 2 Celestion Greenback 25W speakers and also comes with a footswitchable tremolo effect.

If you're looking for that sensuous, creamy early Clapton sound, we guarantee that you'll find it in this beautifully reissued Marshall combo. The natural tone and overdrive of the 1962 Bluesbreaker Amp will quickly become a fundamental ingredient in your overall sound.

Marshall 1962 Bluesbreaker Combo Amp - Scratch 'n' Dent As Is Specifications:

• 29-1/4"W x 23-3/4"H x 10-1/2"D (740 x 600 x 265mm)
• 66.6 lbs. (30.2kg)

Marshall 1962 Bluesbreaker Combo Amp - Scratch 'n' Dent As Is Features:

• 30W output
• 2 - 12" 25W Celestion Greenback speakers
• Valve rectifier
• Footswitchable tremolo effect

Looking for authentic British blues tones? Put it in the cart!

Vintage overdrive-soaked sounds for the stage and studio!

The Marshall 1974X 18W 1x12 Combo Amp is a handwired reissue of the model 1974, a combo originally produced from 1965 to 1968. Introduced as a practice combo amp in 1965, it wasn't as loud as the terror-inducing heads Marshall was producing, but it could rock, giving up incredible lead and crunch sounds at low volumes. The 1974X combo comes with 2 EL84 tubes in the power amp, 3 ECC83s in the preamp, an EZ81 rectifier tube, and features valve-driven tremolo. A proprietary, aged reissue of the 20W, ceramic magnet Celestion T1221 speaker used in the original adds to the Marshall 1974X's tonal authenticity. Marshall includes a footswitch with your 1974X Combo Amp.

Marshall 1974X Handwired 18W 1x12 Combo Amp Specifications:

• 24"W x 20"H x 9"D
• 42 lbs.

Marshall 1974X Handwired 18W 1x12 Combo Amp Features:

• Handwired reissue of the model 1974
• 18W
• 2 EL84 power tubes
• 3 ECC83 preamp tubes
• EZ81 rectifier tube
• Tube-driven tremolo
• Aged reissue 12" Celestion T1221

Simple, easy-to-overdrive, and tons of fun! Order today!

Vintage overdrive-soaked sounds for the stage and studio!

The Marshall 1974X 18W 1x12 Combo Amp is a handwired reissue of the model 1974, a combo originally produced from 1965 to 1968. Introduced as a practice combo amp in 1965, it wasn't as loud as the terror-inducing heads Marshall was producing, but it could rock, giving up incredible lead and crunch sounds at low volumes. The 1974X combo comes with 2 EL84 tubes in the power amp, 3 ECC83s in the preamp, an EZ81 rectifier tube, and features valve-driven tremolo. A proprietary, aged reissue of the 20W, ceramic magnet Celestion T1221 speaker used in the original adds to the Marshall 1974X's tonal authenticity. Marshall includes a footswitch with your 1974X Combo Amp.

Marshall 1974X Handwired 18W 1x12 Combo Amp - Scratch 'n' Dent As Is Specifications:

• 24"W x 20"H x 9"D
• 42 lbs.

Marshall 1974X Handwired 18W 1x12 Combo Amp - Scratch 'n' Dent As Is Features:

• Handwired reissue of the model 1974
• 18W
• 2 EL84 power tubes
• 3 ECC83 preamp tubes
• EZ81 rectifier tube
• Tube-driven tremolo
• Aged reissue 12" Celestion T1221

Simple, easy-to-overdrive, and tons of fun! Order today!

Real all-tube vintage flavor from the original maker.

This half stack includes the Marshall 1987XL Vintage Series 50W Tube Head and Marshall 1960AX or 1960BX 100W 4x12 Guitar Extension Cabinet.

1987XL Vintage Series 50W Tube Head
The Marshall 1987XL Vintage Series 50W Tube Head gives you all the fabulous tube tone of the original 1987X from the 1966 to 1969 era plus a true bypass series FX loop. 3 ECC83 tubes in the preamp and 2 EL34s in the power section dish out that delicious, nasty overdrive behind Hendrix, Townshend, and scores of other greats. 3-band EQ and presence controls provide all the tweakage necessary to get the most out of this classic screamer. 50W. 26"W x 8"H x 10"D. 34 lbs.

Marshall 1960X 100W 4x12 Guitar Extension Cabinet
The Marshall 1960X cab consists of 4 separate birch ply speaker enclosures, each loaded with a Celestion G12M Greenback 12" speaker and has a 100W power handling rating. Tonally this speaker cabinet falls between the 1960A's brightness and the 1960TV's warmth. Greenback G12M speakers have a very distinctive sound with a fast, snappy response that adds detail and dynamics to both clean and distorted playing. The 1960X Extension Cabinet uses the early '70s LC checkered grille cloth and a less-textured vinyl covering. If used as a half stack with a 100W head, a power brake is recommended.

Marshall 1987XL and 1960AX or 1960BX Half Stack Features:

• 1987XL Vintage Series 50W Tube Head
• 50W of classic all-tube power
• 3 ECC83 tubes in the preamp
• 2 EL34s in the power section
• 3-band EQ
• Presence control
  
  Marshall 1960X 100W 4x12 Guitar Extension Cabinet
• 4 - 12" Celestion Greenback G12M speakers
• 100W handling
• Checkered grille cloth
• Straight or Angled front
• 100 lbs

To get the real sound, go for the real deal. Order today!

A killer package that'll save you a C-note.

The 1987XL head:

All the fabulous tube tone of the original 1987X from the 1966 to 1969 era plus a true bypass series FX loop. 3 ECC83 tubes in the preamp and 2 EL34s in the power section dish out that delicious, nasty overdrive behind Hendrix, Townshend, and scores of other greats. 3-band EQ and presence controls provide all the tweakage necessary to get the most out of this classic screamer. 50W. 26"W x 8"H x 10"D. 34 lbs.

The 1960TV cab:

This classic cab has an angled front; 4 - 12" Greenback speakers; and a warmer, thicker sound than the 1960A. The midrange is well-defined and a more rounded high-end sparkles without being overly bright. The 25W Greenbacks are less in your face than the 75W Celestions in the 1960A. It has reissue original grille cloth and is 3" taller than standard 4x12 cabs. Handles 100W. 29-3/5"W x 35-1/2"H x 14-4/5"D.

Marshall 1987XL Head and 1960TV Cab Half Stack Features:

• The head:
• 50W of classic all-tube power
• 3 ECC83 tubes in the preamp
• 2 EL34s in the power section
• 3-band EQ
• Presence control
• 1960TV:
• Angled front
• 4 - 12" 25W Celestion Greenback speakers
• Original grille cloth
• 3" taller than standard 4x12 cabs
• Handles 100W
• 29-3/5"W x 35-1/2"H x 14-4/5"D.
• 97 lbs.

Save $100 when you buy the 2 together. Order now!

Real all-tube vintage flavor from the original maker.

Channel the ghost of Hendrix with this Marshall Full Stack featuring the 1978XL Vintage series 50W Tube Head with 1960AX/1960BX 100W 4 x 12 Guitar Extension Cabinets.

1987XL Vintage Series 50W Tube Head
The Marshall 1987XL Vintage Series 50W Tube Head gives you all the fabulous tube tone of the original 1987X from the 1966 to 1969 era plus a true bypass series FX loop. 3 ECC83 tubes in the preamp and 2 EL34s in the power section dish out that delicious, nasty overdrive behind Hendrix, Townshend, and scores of other greats. 3-band EQ and presence controls provide all the tweakage necessary to get the most out of this classic screamer.

1960AX and 1960BX 100W 4x12 Guitar Extension Cabinets
The Marshall 1960X consists of 4 separate birch ply speaker enclosures, each loaded with a Celestion G12M Greenback 12" speaker and has a 100W power handling rating. Tonally this speaker cabinet falls between the 1960A's brightness and the 1960TV's warmth. Greenback G12M speakers have a very distinctive sound with a fast, snappy response that adds detail and dynamics to both clean and distorted playing. The 1960X Extension Cabinet uses the early '70s LC checkered grille cloth and a less-textured vinyl covering. If used as a half stack with a 100W head, a power brake is recommended.

Marshall 1987XL, 1960AX, and 1960BX Full Stack Specifications:

• 1987XL Vintage Series 50W Tube Head
• 26"W x 8"H x 10"D
• 34 lbs.

Marshall 1987XL, 1960AX, and 1960BX Full Stack Features:

• 1987XL Vintage Series 50W Tube Head
• 50W of classic all-tube power
• 3 ECC83 tubes in the preamp
• 2 EL34s in the power section
• 3-band EQ
• Presence control
  
  1960AX and 1960BX 100W 4x12 Guitar Extension Cabinet
• 4 x 12 Celestion Greenback G12M speakers
• 100W handling
• Checkered grille cloth
• Straight or Angled front
• 100 lbs.

To get the real sound, go for the real deal. Order today!

20W of tube-tone heaven.

Harken back to the golden age of rock and roll with this Marshall Half Stack featuring two classics together, the 2061X Handwired 20W Amp Head and a 2061CX 2x12 Extension Cabinet.

2061X Handwired 20W Amp Head
The Marshall 2061X 20W Amp Head is a hand-wired reissue of the model 2061, a "Lead and Bass" head originally produced from 1967 to 1973. With 20W of power, it churned out golden crunchy tones with depth and character. The Marshall 2061X head comes with 2 EL84 tubes in the power amp, 2 ECC83s in the preamp, and a solid state rectifier.

2061CX 2x12 Extension Cabinet
The Marshall 2061CX cab is a hand-soldered, 60W, 2x12" angled speaker cabinet that matches the 2061X. Loaded with reissue 30W Celestion G12H speakers.

Marshall 2061X and 2061CX 2x12 Half Stack Features:

• 2061X Handwired 20W Amp Head
• Hand-wired reissue of the 2061 "Lead and Bass" head
• 20W
• 2 EL84 tubes in the power amp
• 2 ECC83s in the preamp
• Solid state rectifier
  
  2061CX 2x12 Extension Cabinet
• Hand soldered
• 60W
• 2x12" reissue 30W Celestion G12H speakers

The sound you've dreamed of, delivered to your door. Order today.

20W of tube-tone heaven.

The Marshall 2061X 20W Amp Head is a hand-wired reissue of the model 2061, a "Lead and Bass" head originally produced from 1967 to 1973. With 20W of power, it churned out golden crunchy tones with depth and character. The Marshall 2061X comes with 2 EL84 tubes in the power amp, 2 ECC83s in the preamp, and a solid state rectifier.

Marshall 2061X Handwired 20W Amp Head Features:

• Hand-wired reissue of the 2061 "Lead and Bass" head
• 20W
• 2 EL84 tubes in the power amp
• 2 ECC83s in the preamp
• Solid state rectifier

It's like the amp stepped out of 1968 and into your hand. Order today.

20W of tube-tone heaven.

The Marshall 2061X 20W Amp Head is a hand-wired reissue of the model 2061, a "Lead and Bass" head originally produced from 1967 to 1973. With 20W of power, it churned out golden crunchy tones with depth and character. The Marshall 2061X comes with 2 EL84 tubes in the power amp, 2 ECC83s in the preamp, and a solid state rectifier.

Marshall 2061X Handwired 20W Amp Head - Scratch 'n' Dent As Is Features:

• Hand-wired reissue of the 2061 "Lead and Bass" head
• 20W
• 2 EL84 tubes in the power amp
• 2 ECC83s in the preamp
• Solid state rectifier

It's like the amp stepped out of 1968 and into your hand. Order today.

100 watts of insane power and Slayer tone!

The all-valve Kerry King Signature JCM800 2203KK is the essence of simplicity-a single-channel tube amp with no reverb or effects. It's easy control panel, distinctive roar, and larger than life edge has set the standard by which many rock amps are judged.

This Kerry King model features a switchable Kerry King signature sound section called "The Beast" that has two adjustable controls -"Assault" & "Gate." "Assault" intensity controls the extent of Kerry's signature EQ boost, and "Gate" is an adjustable, studio-quality, ultra-fast noise reduction unit. The 3-band EQ gives you plenty of control, but the base tone of this amp is patterned after the reverse-shape EQ setting used by Kerry himself! Eye-catching tribal graphics blaze from the front panel and baffle. Jim Marshall and Kerry King's signature's on the control panel identify its pedigree.

One of the nicest surprises: Marshall has added functionality to the amp, while lowering the price!

Marshall 2203KK Kerry King Signature JCM800 Guitar Amp Head Specifications:

• 30"W x 9"H x 12"D
• 41 lbs.

Marshall 2203KK Kerry King Signature JCM800 Guitar Amp Head Features:

• 100W valve head
• 4 KT88s in the power stage
• 3 ECC83s in the preamp
• Master Volume
• Preamp Volume
• Standby Switch
• 3-band EQ
• Presence control
• "The Beast" Boost
• Gate Threshold
• Assault Intensity
• Jim Marshall and Kerry King signatures on control panel
• Made in England

Don't wait! Call or click today to order.