Real all-tube vintage flavor from the original maker.

This half stack includes the Marshall 1987XL Vintage Series 50W Tube Head and Marshall 1960AX or 1960BX 100W 4x12 Guitar Extension Cabinet.

1987XL Vintage Series 50W Tube Head
The Marshall 1987XL Vintage Series 50W Tube Head gives you all the fabulous tube tone of the original 1987X from the 1966 to 1969 era plus a true bypass series FX loop. 3 ECC83 tubes in the preamp and 2 EL34s in the power section dish out that delicious, nasty overdrive behind Hendrix, Townshend, and scores of other greats. 3-band EQ and presence controls provide all the tweakage necessary to get the most out of this classic screamer. 50W. 26"W x 8"H x 10"D. 34 lbs.

Marshall 1960X 100W 4x12 Guitar Extension Cabinet
The Marshall 1960X cab consists of 4 separate birch ply speaker enclosures, each loaded with a Celestion G12M Greenback 12" speaker and has a 100W power handling rating. Tonally this speaker cabinet falls between the 1960A's brightness and the 1960TV's warmth. Greenback G12M speakers have a very distinctive sound with a fast, snappy response that adds detail and dynamics to both clean and distorted playing. The 1960X Extension Cabinet uses the early '70s LC checkered grille cloth and a less-textured vinyl covering. If used as a half stack with a 100W head, a power brake is recommended.

Marshall 1987XL and 1960AX or 1960BX Half Stack Features:

• 1987XL Vintage Series 50W Tube Head
• 50W of classic all-tube power
• 3 ECC83 tubes in the preamp
• 2 EL34s in the power section
• 3-band EQ
• Presence control
  
  Marshall 1960X 100W 4x12 Guitar Extension Cabinet
• 4 - 12" Celestion Greenback G12M speakers
• 100W handling
• Checkered grille cloth
• Straight or Angled front
• 100 lbs

To get the real sound, go for the real deal. Order today!

A killer package that'll save you a C-note.

The 1987XL head:

All the fabulous tube tone of the original 1987X from the 1966 to 1969 era plus a true bypass series FX loop. 3 ECC83 tubes in the preamp and 2 EL34s in the power section dish out that delicious, nasty overdrive behind Hendrix, Townshend, and scores of other greats. 3-band EQ and presence controls provide all the tweakage necessary to get the most out of this classic screamer. 50W. 26"W x 8"H x 10"D. 34 lbs.

The 1960TV cab:

This classic cab has an angled front; 4 - 12" Greenback speakers; and a warmer, thicker sound than the 1960A. The midrange is well-defined and a more rounded high-end sparkles without being overly bright. The 25W Greenbacks are less in your face than the 75W Celestions in the 1960A. It has reissue original grille cloth and is 3" taller than standard 4x12 cabs. Handles 100W. 29-3/5"W x 35-1/2"H x 14-4/5"D.

Marshall 1987XL Head and 1960TV Cab Half Stack Features:

• The head:
• 50W of classic all-tube power
• 3 ECC83 tubes in the preamp
• 2 EL34s in the power section
• 3-band EQ
• Presence control
• 1960TV:
• Angled front
• 4 - 12" 25W Celestion Greenback speakers
• Original grille cloth
• 3" taller than standard 4x12 cabs
• Handles 100W
• 29-3/5"W x 35-1/2"H x 14-4/5"D.
• 97 lbs.

Save $100 when you buy the 2 together. Order now!

Real all-tube vintage flavor from the original maker.

The Marshall 1987XL Vintage Series 50W Tube Head gives you all the fabulous tube tone of the original 1987X from the 1966 to 1969 era plus a true bypass series FX loop. 3 ECC83 tubes in the preamp and 2 EL34s in the power section dish out that delicious, nasty overdrive behind Hendrix, Townshend, and scores of other greats. 3-band EQ and presence controls provide all the tweakage necessary to get the most out of this classic screamer.

Marshall 1987XL Vintage Series 50W Tube Head Specifications:

• 26"W x 8"H x 10"D
• 34 lbs.

Marshall 1987XL Vintage Series 50W Tube Head Features:

• 50W of classic all-tube power
• 3 ECC83 tubes in the preamp
• 2 EL34s in the power section
• 3-band EQ
• Presence control

To get the real sound, go for the real deal. Order today!

Real all-tube vintage flavor from the original maker.

Channel the ghost of Hendrix with this Marshall Full Stack featuring the 1978XL Vintage series 50W Tube Head with 1960AX/1960BX 100W 4 x 12 Guitar Extension Cabinets.

1987XL Vintage Series 50W Tube Head
The Marshall 1987XL Vintage Series 50W Tube Head gives you all the fabulous tube tone of the original 1987X from the 1966 to 1969 era plus a true bypass series FX loop. 3 ECC83 tubes in the preamp and 2 EL34s in the power section dish out that delicious, nasty overdrive behind Hendrix, Townshend, and scores of other greats. 3-band EQ and presence controls provide all the tweakage necessary to get the most out of this classic screamer.

1960AX and 1960BX 100W 4x12 Guitar Extension Cabinets
The Marshall 1960X consists of 4 separate birch ply speaker enclosures, each loaded with a Celestion G12M Greenback 12" speaker and has a 100W power handling rating. Tonally this speaker cabinet falls between the 1960A's brightness and the 1960TV's warmth. Greenback G12M speakers have a very distinctive sound with a fast, snappy response that adds detail and dynamics to both clean and distorted playing. The 1960X Extension Cabinet uses the early '70s LC checkered grille cloth and a less-textured vinyl covering. If used as a half stack with a 100W head, a power brake is recommended.

Marshall 1987XL, 1960AX, and 1960BX Full Stack Specifications:

• 1987XL Vintage Series 50W Tube Head
• 26"W x 8"H x 10"D
• 34 lbs.

Marshall 1987XL, 1960AX, and 1960BX Full Stack Features:

• 1987XL Vintage Series 50W Tube Head
• 50W of classic all-tube power
• 3 ECC83 tubes in the preamp
• 2 EL34s in the power section
• 3-band EQ
• Presence control
  
  1960AX and 1960BX 100W 4x12 Guitar Extension Cabinet
• 4 x 12 Celestion Greenback G12M speakers
• 100W handling
• Checkered grille cloth
• Straight or Angled front
• 100 lbs.

To get the real sound, go for the real deal. Order today!

The only cab for your 2061X.

The Marshall 2061CX is a hand-soldered, 60W, 2x12" angled speaker cabinet that matches the 2061X. Loaded with reissue 30W Celestion G12H speakers.

Marshall 2061CX 2x12 Extension Cabinet Features:

• Hand soldered
• 60W
• 2x12" reissue 30W Celestion G12H speakers

The sound you've dreamed of, delivered to your door. Order today.

20W of tube-tone heaven.

Harken back to the golden age of rock and roll with this Marshall Half Stack featuring two classics together, the 2061X Handwired 20W Amp Head and a 2061CX 2x12 Extension Cabinet.

2061X Handwired 20W Amp Head
The Marshall 2061X 20W Amp Head is a hand-wired reissue of the model 2061, a "Lead and Bass" head originally produced from 1967 to 1973. With 20W of power, it churned out golden crunchy tones with depth and character. The Marshall 2061X head comes with 2 EL84 tubes in the power amp, 2 ECC83s in the preamp, and a solid state rectifier.

2061CX 2x12 Extension Cabinet
The Marshall 2061CX cab is a hand-soldered, 60W, 2x12" angled speaker cabinet that matches the 2061X. Loaded with reissue 30W Celestion G12H speakers.

Marshall 2061X and 2061CX 2x12 Half Stack Features:

• 2061X Handwired 20W Amp Head
• Hand-wired reissue of the 2061 "Lead and Bass" head
• 20W
• 2 EL84 tubes in the power amp
• 2 ECC83s in the preamp
• Solid state rectifier
  
  2061CX 2x12 Extension Cabinet
• Hand soldered
• 60W
• 2x12" reissue 30W Celestion G12H speakers

The sound you've dreamed of, delivered to your door. Order today.

20W of tube-tone heaven.

The Marshall 2061X 20W Amp Head is a hand-wired reissue of the model 2061, a "Lead and Bass" head originally produced from 1967 to 1973. With 20W of power, it churned out golden crunchy tones with depth and character. The Marshall 2061X comes with 2 EL84 tubes in the power amp, 2 ECC83s in the preamp, and a solid state rectifier.

Marshall 2061X Handwired 20W Amp Head Features:

• Hand-wired reissue of the 2061 "Lead and Bass" head
• 20W
• 2 EL84 tubes in the power amp
• 2 ECC83s in the preamp
• Solid state rectifier

It's like the amp stepped out of 1968 and into your hand. Order today.

20W of tube-tone heaven.

The Marshall 2061X 20W Amp Head is a hand-wired reissue of the model 2061, a "Lead and Bass" head originally produced from 1967 to 1973. With 20W of power, it churned out golden crunchy tones with depth and character. The Marshall 2061X comes with 2 EL84 tubes in the power amp, 2 ECC83s in the preamp, and a solid state rectifier.

Marshall 2061X Handwired 20W Amp Head - Scratch 'n' Dent As Is Features:

• Hand-wired reissue of the 2061 "Lead and Bass" head
• 20W
• 2 EL84 tubes in the power amp
• 2 ECC83s in the preamp
• Solid state rectifier

It's like the amp stepped out of 1968 and into your hand. Order today.

100 watts of insane power and Slayer tone!

The all-valve Kerry King Signature JCM800 2203KK is the essence of simplicity-a single-channel tube amp with no reverb or effects. It's easy control panel, distinctive roar, and larger than life edge has set the standard by which many rock amps are judged.

This Kerry King model features a switchable Kerry King signature sound section called "The Beast" that has two adjustable controls -"Assault" & "Gate." "Assault" intensity controls the extent of Kerry's signature EQ boost, and "Gate" is an adjustable, studio-quality, ultra-fast noise reduction unit. The 3-band EQ gives you plenty of control, but the base tone of this amp is patterned after the reverse-shape EQ setting used by Kerry himself! Eye-catching tribal graphics blaze from the front panel and baffle. Jim Marshall and Kerry King's signature's on the control panel identify its pedigree.

One of the nicest surprises: Marshall has added functionality to the amp, while lowering the price!

Marshall 2203KK Kerry King Signature JCM800 Guitar Amp Head Specifications:

• 30"W x 9"H x 12"D
• 41 lbs.

Marshall 2203KK Kerry King Signature JCM800 Guitar Amp Head Features:

• 100W valve head
• 4 KT88s in the power stage
• 3 ECC83s in the preamp
• Master Volume
• Preamp Volume
• Standby Switch
• 3-band EQ
• Presence control
• "The Beast" Boost
• Gate Threshold
• Assault Intensity
• Jim Marshall and Kerry King signatures on control panel
• Made in England

Don't wait! Call or click today to order.

Vintage rock tones with modern features and high gain!

The Marshall Vintage Modern 2466 Half-Stack includes the Vintage Modern 2466 Tube Amp Head and Vintage Modern 425A angled speaker enclosure.

The Marshall Vintage Modern 2466 Tube Amp Head is an all-valve amplifier with a choice of two dynamic ranges selectable by footswitch. The Low range delivers the performance you would expect from a stock vintage Marshall amplifier in terms of tone and available gain. The High range adds an extra preamp valve into the signal path, facilitating those classic hard rock tones of the seventies. Add to this the ability to dynamically interface with your instrument's Volume and Tone controls and the experience translates into a truly expressive and organic feel in performance.

Two frequency selective Pre-amp Volumes (Gains) - Body and Detail - facilitate greater flexibility in tone shaping for individual guitars and styles while the power amplifier is heavily influenced by the first Marshall amplifiers to be produced, with four KT66 output valves yielding that substantial, fat and smooth tone. A MID Boost switch on the front panel fattens the tone even more while a traditional Marshall tone control circuit enables fine tuning of your sound.

A master volume has been included in order to practically manage the output levels at all venues. This is implemented after the phase splitter in order to fully exploit maximum preamp drive when the master is turned down low. A reverb level control mixes the on board plate reverb with the direct signal to whatever degree the player chooses. The reverb can be toggled on and off via the footswitch.

Finally, a series FX loop is provided for those players who wish to use outboard effects to further enhance their sound. Loop levels of 10dB and +4dB can be controlled via a rear panel switch as well as the option to completely bypass this feature if it is not required.

The cosmetics are also a carefully crafted hybrid of old and new styles made even more dramatic by the deep purple vinyl that covers the entire series.

The Marshall Vintage Modern 425A angled speaker cab is a traditional Marshall 4 x 12 speaker cabinet in design. Mono/stereo switchable and loaded with G12C 25 Watt Celestion Greenbacks, this was specifically developed for the Limited Edition Jimi Hendrix Super100JH stack and are voiced to give that rich and balanced harmonic timbre that complements vintage tone and the Vintage Modern Series perfectly.

The cosmetics are also a carefully crafted hybrid of old and new styles made even more dramatic by the deep purple vinyl that covers the entire series.

Marshall 2466 and 425A or 425B Half Stack Specifications:

• Head Dimensions: 29-1/2" x 12" x 9" (750 x 310 x 230 mm)
• Weight: 49.6 lbs (22.5 kg)
  
  Cabinet
• Impedance
• Mono 16 Ohms/4 Ohms
• Stereo 8 Ohms/8 Ohms
• Dimensions 30.5" x 30" x 14.5" (770 x 755 x 365 mm)
• Weight
• 425A: 79 lbs. (36 kg)

Marshall 2466 and 425A or 425B Half Stack Features:

• 100-Watt valve head
• Valve compliment: 4 x ECC83 (12AX7s) in preamp, 4 x KT66 in power amp
• Master Volume with two Gain Controls Detail (highs) & Body (lows)
• Two footswitchable Dynamic Ranges Low & High
• Mid Boost switch
• Footswitchable Proprietary digital Plate Reverb
• Series FX loop with level switch and bypass
• Made in England
  
  100-Watt, 4x12" cabinet
• Angled front
• Loaded with Celestion G12C 25 Greenbacks
• Mono or Stereo switchable
• 16 Ohms/4 Ohms mono
• 8 Ohms stereo
• Birch ply construction
• "finger-locking" joints
• Made in England

This half-stack rocks with its classic Marshall sound and modern high-gain edge! Make it yours. Order today.

Vintage rock tones with modern features and high levels of gain!

The Marshall Vintage Modern 2466 Full-Stack includes the Vintage Modern 2466 Tube Amp Head, Vintage Modern 425A angled speaker cabinet and Vintage Modern 425B straight speaker cab.

The Marshall Vintage Modern 2466 Tube Amp Head is an all-valve amplifier with a choice of two dynamic ranges selectable by footswitch. The Low range equates equates to the performance you would come to expect from a stock vintage Marshall amplifier in terms of tone and available gain. The High range adds an extra preamp valve into the signal path, facilitating those classic hard rock tones of the seventies. Add to this the ability to dynamically interface with your instrument's Volume and Tone controls and the experience translates into a truly expressive and organic feel in performance.

Two frequency selective Pre-amp Volumes (Gains) - Body and Detail - facilitate greater flexibility in tone shaping for individual guitars and styles while the power amplifier is heavily influenced by the first Marshall guitar amplifiers to be produced, with four KT66 output valves yielding that substantial, fat and smooth tone. A MID Boost switch on the front panel fattens the tone even more while a traditional Marshall tone control circuit enables fine tuning of your sound.

A master volume has been included in order to practically manage the output levels at all venues. This is implemented after the phase splitter in order to fully exploit maximum preamp drive when the master is turned down low. A reverb level control mixes the on board plate reverb with the direct signal to whatever degree the player chooses. The reverb can be toggled on and off via the footswitch.

Finally, a series FX loop is provided for those players who wish to use outboard effects to further enhance their sound. Loop levels of 10dB and +4dB can be controlled via a rear panel switch as well as the option to completely bypass this feature if it is not required.

The cosmetics are also a carefully crafted hybrid of old and new styles made even more dramatic by the deep purple vinyl that covers the entire speaker series.

The Marshall Vintage Modern 425A angled cab and 425B straight cab are traditional Marshall 4 x 12 speaker enclosures in design. These cabs are mono/stereo switchable and are loaded with G12C 25 Watt Celestion Greenbacks. These were specifically developed for the Limited Edition Jimi Hendrix Super100JH stack and are voiced to give that rich and balanced harmonic timbre that complements vintage tone and the Vintage Modern Series perfectly.

The cosmetics are also a carefully crafted hybrid of old and new styles made even more dramatic by the deep purple vinyl that covers the entire series.

Marshall 2466, 425A, and 425B Full Stack Specifications:

• Head Dimensions: 29-1/2" x 12" x 9" (750 x 310 x 230 mm)
• Weight: 49.6 lbs (22.5 kg)
  
  Cabinet
• Impedance
• Mono 16 Ohms/4 Ohms
• Stereo 8 Ohms/8 Ohms
• Dimensions 30.5" x 30" x 14.5" (770 x 755 x 365 mm)
• Weight
• 425A: 79 lbs. (36 kg)
• 425B: 81.5 lbs (37 kg)

Marshall 2466, 425A, and 425B Full Stack Features:

• 100-Watt valve head
• Valve compliment: 4 x ECC83 (12AX7s) in preamp, 4 x KT66 in power amp
• Master Volume with two Gain Controls Detail (highs) & Body (lows)
• Two footswitchable Dynamic Ranges Low & High
• Mid Boost switch
• Footswitchable Proprietary digital Plate Reverb
• Series FX loop with level switch and bypass
• Made in England
  
  100-Watt, 4x12" cabinet
• Angled front
• Loaded with Celestion G12C 25 Greenbacks
• Mono or Stereo switchable
• 16 Ohms/4 Ohms mono
• 8 Ohms stereo
• Birch ply construction
• "finger-locking" joints
• Made in England

Few word combinations are as exciting as "Marshall stack"! Make it yours. Order today.

Get the most out of your Marshall TSL.

The Marshall 5-Button Footswitch for TSL Series Amps makes it easy to controll your TSL. This heavy-duty stompbox gives your foot access to all 3 channels, reverb, and effects.

Marshall 5-Button Footswitch for TSL Series Amps Features:

• Heavy-duty construction
• 5 buttons
• 3-channel access
• Reverb and FX on/off

Keep your fingers on the fretboard and your mind on the music. Order now.

Protective cover for Marshall ATV combo amps

Protect your Marshall investment! This affordable cover will keep your guitar amplifier looking great for years. Made of weather-resistant vinyl and features the Marshall logo in gold.

Fits AVT100, AVT100X, AVT150, and AVT150X Amps.

A good deputy knows when to cover the Marshall. That time is now!

Protective cover for Marshall AVT112 cabinet.

Protect your Marshall investment. This affordable cover will keep your AVT110 speaker looking great for years. Made of weather-resistant vinyl and features the Marshall logo.

A good deputy knows when to cover the Marshall. That time is now!

Protective cover for Marshall ATV150 head.

Protect your Marshall investment! This affordable cover will keep your gear looking great for years. All Made of weather-resistant vinyl and features the Marshall logo in gold.

Approximate Dimensions: 26.44" x 10.68" x 9.85"

A good deputy knows when to cover the Marshall. That time is now!

Protective cover for Marshall AVT20 combo amp.

Protect your Marshall investment! This affordable cover will keep your AVT20 or AVT20X amp looking great for years. Made of weather-resistant vinyl and features the Marshall logo in gold.

Approximate Dimensions 19" x 18.4" x 10.7"

A good deputy knows when to cover the Marshall. That time is now!

Protective cover for Marshall AVT275 combo amp.

Made of tear resistant material, this cover keeps dust and dirt out of your amp head's delicate parts to prolong life and prevent against knob-turning noise.

A good deputy knows when to cover the Marshall. That time is now!

Protective cover for Marshall AVT412A cabinet.

Protect your Marshall investment! This affordable cover will keep your guitar amp looking great for years. All made of weather-resistant vinyl and features the Marshall logo in gold.

Fits Marshall AVT412A.

A good deputy knows when to cover the Marshall. That time is now!

Protective cover for Marshall AVT50 combo amp.

Protect your Marshall investment! This affordable cover will keep your guitar's amplifier looking great for years. All made of weather-resistant vinyl and features the Marshall logo in gold.

Approximate Dimensions: 20.3 x 21.9 x 10.25"

A good deputy knows when to cover the Marshall. That time is now!

Protective cover for Marshall AVT50H head.

Protect your Marshall investment! This affordable cover will keep your guitar amp looking great for years. All made of weather-resistant vinyl and features the Marshall logo in gold.

Fits Marshall AVT50H.

A good deputy knows when to cover the Marshall. That time is now!