Small in size, but large in sound and shaping options.

The Markbass CMD 151P is a bass combo amplifier equipped with Markbass' flagship solid state preamp, the Little Mark II. Despite being a Mini model, the CMD 151P amp gives you maximum power and sound. The amp provides plenty of power to blow through the high-quality 15" B&C woofer and piezo tweeter. The CMD 151P also has 2 speaker outs which allow you to hook up to another 8 ohm extension cab, giving you a 500W rig! The Little Mark II has a 4-band EQ, as well as two exclusive Markbass' filters for rounding out your tone to perfection. A handle on top makes Markbass CMD 151P amp easy to transport too.

Markbass Mini CMD 151P 300/500W 1x15 Bass Combo Amp Specifications:

• Speaker: 1 x 15"
• Tweeter: piezo
• Bass reflex: rear
• Impedance: 8 ohms
• Sensitivity: 100 dB SPL
• Speaker power handling: 400W RMS (AES Standard)
• Frequency response: 40Hz to 18kHz
• Crossover Frequency: 3.5kHz
• Dimensions: 18.27"W x 18.27"H x 18.9"D
• Weight: 40.79 lbs.
  
  Little Mark II head
• Power
• Input impedance: 500Kohm, max. voltage: 15 Vpp
• Balanced Output (XLR): 22Kohm, max. voltage 25 Vpp
• Effect Return impedance: 22Kohm, max. voltage: 25 Vpp
• Output Power: 300W RMS at 8 ohm, 500W RMS at 4 ohm
• Power requirement: 100/120V; 230V; 240V; 50/60Hz
• Controls
• GAIN 80 dB to +23 dB range
• MASTER VOLUME
• GROUND LIFT: switch on rear panel
• Equalization
• LOW
• Center frequency: 40Hz; level ±16dB
• LOW MID
• Center frequency 360Hz, level ±16dB
• HIGH MID
• Center frequency 800Hz, level ±16dB
• HIGH
• 10kHz shelf; level ±16dB
• VPF (Variable Pre-shape Filter)
• center frequency 380Hz (cut)
• VLE (Vintage Loudspeaker Emulator)
• frequency range 250Hz 20kHz (cut)
• Outputs
• EFFECT SEND
• Unbalanced, max. voltage 20 Vpp (pre-EQ)
• TUNER OUT
• Unbalanced, max. voltage 25 Vpp
• LINE OUT
• Balanced XLR, max. voltage 10 Vpp
• SPEAKER OUT
• Speakon, 1/4"

Markbass Mini CMD 151P 300/500W 1x15 Bass Combo Amp Features:

• Built-in Little Mark II solid state preamp on top rear
• 15" B&C woofer
• Piezo tweeter
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Top handle for transportation
• Grill for protecting speaker
• Lightweight
  
  Little Mark II
• Provides 500W at 4 ohm or 300W at 8 ohm
• Gain and Master volume controls
• Clip warning light
• EQ includes controls for Low, Mid Frequency Low, High Frequency Low, and High
• VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters
• Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
• Balanced XLR out
• Ground lift switch to eliminate hum
• Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
• Send and Return Effect ensures main signal continues even if something dies in your effects chain

Don't be fooled by the size and weight of this compact combo. It's sound is bigger than you think. Order today!

Big-time, fat output from a bass combo weighing less than 30 lbs!

The Markbass Mini CMD 121P is a bass combo amplifier that gives you fat sound with electric or acoustic basses. That makes the Mini CMD 121P amp perfect for rehearsal studios or small club applications. The Markbass Mini CMD 121P comes with a built-in Little Mark II bass head in the top rear area. Bassists will appreciate the Markbass-designed Vintage Loudspeaker Emulator and Variable Pre-shape Filter which help give this Mini CMD a warm natural sound. The Little Mark II also has a Neutrik Speakon combo jack output that accepts both Speakon or 1/4" speaker cable as well as a second 1/4" speaker out jack so you can hook up to another 8 ohm cab for a 500W rig. You'll also find a balanced XLR out, unbalanced tuner out so you can tune as you play without passing your signal through pedals. A Send and Return Effect loop protects you from losing your signal if one of your pedals dies or a cable in the chain gives out.

Markbass Mini CMD 121P 1x12 Bass Combo Amp Specifications:

• Impedance: 8 ohms
• Speaker power handling: 400W RMS (AES Standard)
• Frequency Response: 45Hz to 18kHz
• Crossover Frequency: 3.5kHz
• Sensitivity: 99dB SPL
• Weight: 29.3 lbs.
• Dimensions: 15.3"(W) x 17"(H) x 14.1"(D)
  
  Little Mark II head

Markbass Mini CMD 121P 1x12 Bass Combo Amp Features:

• Solid state preamp
• 12" B&C speaker
• Piezo tweeter
• Rear bass reflex
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Lightweight for easy transport
• Handle on top for transporting
• Protected corners
• Grill screen to protect speaker
  
  Little Mark II
• Provides 500W at 4 ohm or 300W at 8 ohm
• Gain and Master volume controls
• Clip warning light
• EQ includes controls for Low, Mid Frequency Low, High Frequency Low, and High
• VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters
• Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
• Balanced XLR out
• Ground lift switch to eliminate hum
• Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
• Send and Return Effect ensures main signal continues even if something dies in your effects chain

Big sound in a small package. What more could you want? Order today!

Small size, big sound.

The Schroeder Mini 12+ Light Bass Cabinet was designed especially for bassists who double on electric and acoustic upright basses. It has all of the features in the same small package as the Mini 12 Light but adds a phenolic super tweeter for an even more sensitive response. It practically prevents upright feedback and is among the smallest single 12" cabinets on the market.

Schroeder Mini 12+ Light Bass Cabinet Features:

• 12" custom steel frame woofer
• Phenolic super tweeter
• 1/4" and Speakon in/out
• 40Hz — 16kHz frequency response
• 8-ohm impedance
• 400W RMS
• 100dB SPL @ 1w/1m maximum
• Weight: 20 lbs.
• Dimensions: 16" x 16" x 16"

Order today and never lug a heavy bass amp again.

Small size, big sound.

The Schroeder Mini 12+ Bass Cabinet was designed especially for bassists who double on electric and acoustic upright basses. It has all of the features in the same small package as the Mini 12, but adds a phenolic super tweeter for an even more sensitive response. It practically prevents upright feedback and is among the smallest single 12" cabinets on the market.

Schroeder Mini 12+ Regular Bass Cabinet Features:

• 12" custom steel frame woofer
• Phenolic super tweeter
• 1/4" and Speakon in/out
• 40Hz — 16kHz frequency response
• 8-ohm impedance
• 500W RMS
• 100dB SPL @ 1w/1m maximum
• Weight: 30 lbs.
• Dimensions: 16" x 16" x 16"

Order today and never lug a heavy bass amp again.

Professional recording quality and features at project studio prices from Apogee.

The Apogee Mini-MP preamplifier takes the reference quality of the Trak2 and the premium Mini-Me preamps to the next level.

The preamp offers an amazing-sounding, affordable, portable mic preamp that is an ideal addition to Apogee conversion systems, mobile studios and pro recording facilities. Just like its Mini-Series siblings, the Mini-MP gives you Apogee quality, without compromise, that you can take anywhere.

You've Got Gain
The Mini-MP features two individual ultra-fast, high-gain and low-distortion preamps, each providing an awesome 75 dB of gain. Adjustment is step-less via a single control knob, so there's no need for pads or other types of noisy switch mode gain adjustments. Another great advantage of a stepless gain control is the ability to adjust levels on the fly without pops and other audible gain. The ultra-linear gain control is also a very useful tool for those who like to "ride" the gain, making the unit a perfect solution for both studio and on-location recording.

Additionally, the Mini-MP Preamp provides a stereo master output gain control. This enables the Mini-MP to feed all types of audio equipment, balanced or unbalanced, from consumer to professional grade.

Keep the Noise Down
A problem with many mic preamplifiers is the noise and distortion they add to the signal. Not the Mini-MP. To maintain a crystal clear, ultra-low distortion audio path, all required switching is accomplished by gas-filled relays, and the use of capacitors in the audio chain has been limited to separating phantom power from the active circuitry only. This results in a considerable reduction in unwanted distortion and provides the clean sound you'd expect from a premium pre-amp.

Ins and Outs
The microphone inputs on the Mini-MP can handle levels up to +18dBu, giving you plenty of headroom. The Mini-MP also offers auto-selected High-Z inputs for instruments and consumer level equipment. This is a great feature for going direct from guitar, bass (or direct out from an amp), and keyboard to your recording device.

On the output side, the Mini-MP uses Apogee's newly developed electronically balanced line drivers which were designed for the Mini-DAC and simulate true transformer behavior. The result is perfect symmetry when used in balanced mode (even with an unsymmetrical load) and no increased distortion when used unbalanced. This circuitry is an ultra low output impedance, high current driver, capable of running levels up to 26dBu to the most complex or low impedance loads, as found in many recording studios utilizing vintage audio-equipment.

Middle-Side Mode
Another exciting feature of the Mini-MP is the selectable Mid-Side (MS) matrix decoder mode. MS is great for recording audio using an MS-configured mic setup, preserving total mono-compatibility or for changing the stereo width of existing L-R recorded material.

The Apogee Mini-MP can run as two completely individual pre-amps or in the Mid-Side mode, where the left channel will be the "Mid" and the right channel the "Side. " In this mode the left output is the "sum" and the right output the "difference. "

Phase, Phantom Power and High-pass filter
The Mini-MP Preamplifier includes a phase switch, phantom power, and a selectable 80Hz High-pass filter with a roll-off of 18dB/oct per channel. Mini-MP's High Pass filter works wonders for vocals, eliminating unwanted lows.

Easy on Energy
The Mini-MP has been specially designed for both field and studio recording, resulting in a premium pre-amp with low power consumption. The Apogee Mini-MP is not critical about its power-supply at all; any DC voltage 6-14 Volt at 1 amp will be sufficient. This gives the Mini-MP owner total flexibility to select from many battery and third party power pack options and the freedom to record any place, anywhere.

Apogee Mini-MP 2-Channel Analog Mic/Instrument Preamp - Scratch 'n' Dent Specifications:

• Pre-amp gain: 0 70 dB
• Output gain: nominal +6 dB
  
  Max input level: +18 dBu
• Max output level, ll @ THD+N <= -98 dB:
• 26 dBu in 100k Ohms
• 24 dBu in 600 Ohms
• 21 dBu in 300 Ohms
  
  THD+N:
• -105 dB at 0 dB of gain
• -96 dB at 40 dB
• -85 dB at 60 dB
  
  Bandwidth:
• 2.5 - > 200kHz(-.5 dB) at 0 dB gain
• 4 160 kHz (-3 dB) at 40 dB
• 4 92 kHz (-3 dB) at 60 dB
  
  EIN: <124 (22-22 kHz) 150 Ohms
  
  < strong>Input impedance:
• Balanced: 1.6k Ohms
• Unbalanced HI-Z: 2.2 M Ohms
  
  Output Impedance: 25 Ohms
  
  HPF:
• 18 dB/oct ( 3rd order Butterworth)
• -3dB at 80 Hz
  
  Phantom power: 48 Volt
• Power: 6 14 VDC, 3W

Apogee Mini-MP 2-Channel Analog Mic/Instrument Preamp - Scratch 'n' Dent Features:

• Superb two-channel microphone preamplifier with phantom power and HI-Z instrument inputs
• Low distortion pre-amps with 75dB of gain. THD+N: 105 dB at unity, -85 dB at 60 dB of gain
• Ultra-linear gain control
• Mid-Side (MS) feature
• 80 Hz Hi-pass filter with a roll off of +18dB/oct
• Low power consumption allowing the use of several types of batteries and third party power packs
• Inputs: 2, combi-jack mic/line inputs (Hi-Z)
• Outputs: 2, XLR analog out

Order with the protection of our 45-day lowest price and total satisfaction guarantees!

An affordable way to get warm analogue sound in your mixes!

Mynx is a simple, elegant and cost effective way to get the depth, clarity and characteristic sound of SSL SuperAnalogue processing into your recordings. The desktop mini X-Rack allows you to load your choice from the X-Rack module range into a simple two module slot desktop box.

Using identical circuit design and manufacturing to our Duality and AWS 900+ consoles, X-Rack is a modular system that delivers the legendary SSL SuperAnalogue sound in a uniquely versatile form. There are eight different modules (Sold Separately) in the range designed to complement your DAW and improve the results you get from the recording process. Mynx enables you to combine different modules to create a range of recording and mixing tools; Combine the 'SuperAnalogue Mic Pre' & 'Dynamics' modules for a pristine front end recording system for vocals. Slot in the 'EQ' & 'Dynamics' modules for versatile and characteristic SSL channel strip processing. Add the 'VHD Input' module to inject analogue warmth or grit. Fit the Stereo Bus Compressor module for legendary 'audio glue' full mix compression. Or fit a 'Master Bus' & 'Line Input' modules to create a analogue monitor and foldback system for your studio.

Mynx is a rugged metal enclosure made from 4mm thick extruded aluminum. It measures a mere 105mm x 190mm x 185mm and has two X-Rack Module capacity. Power supply to the modules is via an external supply and audio connections are made directly to the back of your selected modules.

NOTE: Mynx has no Total Recall capability.

Solid State Logic Mynx XLogic SuperAnalogue Desktop Mini X-Rack Specifications:

• Depth: 7.32 inches/186mm excluding front panel knob(s) and connectors
• Height: 7.56 inches/192mm
• Width: 4.17 inches/106mm
• Weight: 3.6 pounds/1.6kg without modules fitted

Solid State Logic Mynx XLogic SuperAnalogue Desktop Mini X-Rack Features:

• The SSL Mynx chassis supports all of the current X-Rack module range:
• X-Rack Mic Amp Module
• X-Rack VHD Mic Preamp Module
• X-Rack Channel EQ Module
• X-Rack Dynamics Module
• X-Rack Stereo Bus Compressor Module
• X-Rack Four Channel Input Module
• X-Rack Eight Channel Input Module
• X-Rack Master Bus Module
  
  NOTE: All modules sold separately

Save BIG when you buy today!

A Class A Joe Satriani combo you can carry with one hand? You better believe it.

From the Joe Satriani series, the Peavey JSX Mini Colossal Guitar Amp is a great answer to the question of how to get great tube sound out of a small combo amplifier at manageable volumes. The feature that makes it happen is Peavey's trademarked Power Sponge: a unique control that allows the user to adjust the nominal output power level of the amplifier. It can be used in conjunction with the volume control to attain infinite combinations of power amp and preamp distortion at any volume level. This control DOES NOT affect the level of the Microphone Simulated Recording output and provides an appropriate load to the amplifier at all settings.

Speaker outputs are provided as paralleled 1/4" mono tip-sleeve jacks for the connection of speaker enclosures. Minimum speaker impedance is 4 Ohms. You set the cabinet Impedance Selector switch to match the load of the speaker cabinet(s). The internal speaker is 8 Ohms.

A recording out XLR jack is used to route a Microphone Simulated signal (tapped directly from the speaker being used) from the amplifier to an external recording device or PA. It uses a 100% passive circuit to avoid clipping, noise, and other shortcomings of solid-state circuitry.

An 8" speaker is specially voiced to get the absolute best tone out of this combo, whether you're playing clean, crunchy, or full-on distortion.

Peavey hasn't forgotten good looks, either. A stylish black housing is set off by a classic jeweled power light and chrome-plated brass control knobs.

"The JSX Mini Colossal Combo is a Class A monster in a nice little box. It has a pure, wide-open sound, classic tremolo, buffered effects loop, a unique power level attenuator, and a recording output that actually sounds like the amp. Together with a specially voiced 8" speaker, the 5W Mini Colossal has a vintage tone that really rocks. It can run clean, crunchy, or, down and dirty. Its unique design makes it easy to get a good tone fast, and its size makes it very practical. Whether practicing, recording, or, even playing a small gig, this lively little amp really sounds great." Joe Satriani

Peavey JSX Mini Colossal Guitar Amp Specifications:

• Dimensions (H x W x D): 14.38" x 13.75" x 9.38" (365mm" x 350mm" x 238mm")
• Weight: 21.5 lbs. (9.75 kg)
  
  Rated Power: 5 W (RMS @ clipping) into 4, 8, or 16 Ohms (selectable)
• NOTE: Power Sponge attenuator allows for continuous power output adjustment from 0 to 5 Watts
• Power Consumption: 30 W, 60 Hz, 120 VAC
  
  Effects Send
• Low Impedance: 22 kOhms or greater
• Nominal Output Level: 0.5V(RMS), -6.0dBV,
  
  Effects Return
• Input Impedance: 3.9M Ohms
• Nominal Input Level: 0.5V(RMS), -6.0dBV
  
  Recording Output (microphone simulated)
• Output Impedance: 600 Ohms, balanced XLR
• Nominal Output Level: 0.1V(RMS), -20.0 dBV

Peavey JSX Mini Colossal Guitar Amp Features:

• Single Input
• 1 x 12AX7 and 1 x EL84 tube
• Pure Class A operation
• No negative power amp feedback
• Preamp Volume and Tone controls
• 5W (RMS) into 4, 8, or 16 Ohms (selectable impedance)
• Power Sponge output power level attenuator
• Buffered Effects Loop Send and Return jacks
• Classic opto-electronic Tremolo circuit
• Microphone Simulated XLR Recording Output
• XLR Ground Lift switch
• Specially voiced 8" C8R-type speaker
• Classic jeweled pilot light
• Chrome plated brass control knobs

Call or click today to order this mighty mini amp.

Ideal for bassists who play both electric and acoustic uprights.

The Schroeder Mini 12 Light Bass Cabinet was designed especially for bassists who double on electric and acoustic upright. It practically prevents upright feedback, is among the smallest single 12" bass speaker cabinets on the market, and at 22 pounds it is four pounds lighter than the regular Mini 12.

Schroeder Mini 12 Light Bass Cabinet Specifications:

• 12" custom steel frame woofer
• 1/4" and Speakon in/out
• 40hz — 16khz frequency response
• 4-ohm impedance
• 400W RMS
• 100db SPL @ 1w/1m maximum
• Weight: 22 lbs.
• Dimensions: 16" x 16" x 16"

Schroeder Mini 12 Light Bass Cabinet Features:

• 12" custom steel frame woofer
• 1/4" and Speakon in/out
• 40hz — 16khz frequency response
• 4-ohm impedance
• 400W RMS

It redefines the whole notion of bass cabinet portability. Order the Mini 12 Light today.

Ideal for bassists who play both electric and acoustic basses

The Schroeder Mini 12 Bass Cabinet was designed especially for bassists who double on electric and acoustic upright. It practically prevents upright feedback and is among the smallest single 12" cabinets on the market.

Schroeder Mini 12 Bass Cabinet Features:

• 12" custom steel frame woofer
• 1/4" and Speakon in/out
• 40hz — 16khz frequency response
• 8-ohm impedance
• 500W RMS
• 100dB SPL @ 1w/1m maximum
• Weight: 26 lbs.
• Dimensions: 16" x 16" x 16"

Sweet sounding and easy to move. Order the Mini 12 today.

A wall of screaming stacks pumped directly into your brain!

The Rockman Metal Ace is a high-quality, low-priced headphone amp that offers built-in compression, volume control, and auxiliary stereo input/output. Use it to jam along with your favorite bands. Killer distortion with switchable gain. Sound so heavy, many a serious metal monster have used this thing as a studio direct box or a distortion unit in front of their amps.

Rockman Metal Ace Headphone Amp Features:

• Killer metal tones
• Switchable gain
• Compression
• Volume control
• Stereo in and out

You won't believe how cool the tone is. It's a truly sustainful, biting distortion. Put it in the cart.

Full-stack sounds from a tiny box you can carry in your pocket.

The Rockman Guitar Ace headphone amp lets you hear your instrument's dynamic range and clarity to inspire you to "pick up your guitar and play". This high-quality, low-priced headphone amps offers built-in compression, volume control, and auxiliary stereo input/output. You can even route the output to a mixer for recording! The Guitar Ace offers pristine clean, semi, and heavy distortion.

Rockman Guitar Ace Headphone Amp Features:

• Built-in compression
• Volume control and auxiliary stereo input/output
• Route the output to a mixer for recording
• Pristine clean, semi, and heavy distortion

Order it today and practice all night without disturbing your roommate.

Practice anywhere, anytime.

The high-quality Rockman Bass Ace Headphone Amp features built-in compression, volume control, and auxiliary stereo input/output. You can even route the output to a mixer for recording! The Rockman Bass Ace offers selectable treble/mid boost to add to your sound.

Rockman Bass Ace Headphone Amp Features:

• Built-in compression
• Volume control
• Auxiliary stereo input/output
• Selectable treble/mid boost

You'll love the sound and the convenience of quiet practice at full volume. Order today.

Amp modeling in a go anywhere, play anytime unit.

The Waves iGTR Headphone Amp is a pocket-sized and power-packed personal guitar effects processor that delivers the real sound of guitar amps and effects, anytime, anyplace. Strap it on, plug in your guitar, and you're ready to rock. Hook up headphones or speakers and unleash the power of iGTR: Cutting-edge guitar tones-from cool clean sounds to scorching distortion-at your fingertips.

Plug your mp3 player into Waves iGTR to play along with your favorite tunes, or chain together 2 iGTRs to jam with friends-any time of the day or night, without waking the neighbors!

The Wave iGTR's powerful amps and effects let you fine-tune your tone for maximum sound.

Ambience FX
From sparkling to spacious, when you need some atmosphere to fatten up your sound, iGTR's three tweakable ambience effects will make your guitar tone larger than life. Settings include Reverb, Chorus, and Delay.

Modulation FX
From cool and mild to wet and wild, turn your tone inside out with iGTR's three variable speed modulation effects. Shimmering highs and pulsating waves of sound are yours at the flip of a switch. Settings include Phaser, Tremolo, and Wah.

Amps
From smooth jazz to crunchy metal, iGTR's three virtual amps with adjustable drive give you the power to dial up your sound instantly and intuitively. For sizzling lead lines, blistering riffs, stinging solos, and walls of distortion, iGTR has it all. Settings include Warm, Normal, and Bright.

How to use iGTR:
Pop in 4 AAA batteries.
Hook up your headphones.
Plug in your guitar.
Strap on iGTR with the belt clip.
Turn on iGTR.
Pick your amp and effects.
Tweak the controls to find your sound.
You are now ready to rock.

At home. At the beach. Between classes. On the road. On the go. Wherever inspiration strikes, iGTR is ready. Order yours now.

The world's smallest full-featured guitar amp.

The C Tech V2 Pocket Rockit Headphone Amplifier captures the tonal heritage of 50 years of guitar amp design. It combines analog and digital signal processing to reproduce classic tube amp tones. A proprietary DSP engine provides awesome digital effects such as reverb, delay, chorus, and flange, while an analog front end generates classic amp emulation tones.

You don't even need a cable. Like all Pocket Rockit products, the V2 plugs directly into any guitar. Just plug it in, put on your headphones and you're ready to rock 'n' roll. You can even play along with your favorite CD. Best of all, the V2 sounds better than many full-blown amplifiers.

The C Tech V2's amp emulation circuitry models vintage and current classics. The Clean amp button scrolls through 3 clean or slightly over-driven tones. The Dirty amp button scrolls through 3 gnarly, positively nasty high-gain selections. Sounds reminiscent of classic Fender, Marshall, Soldano and other amps are at your fingertips.

This headphone amp has 2 independent DSP effect banks: a delay bank with straight delay, flange, and chorus: and a reverb bank that includes arena reverb, small-hall reverb, and an echo effect. Use any effect independently, or use one from each bank simultaneously.

A digital tuner features audible low-E, A, D, G, B and high-E notes. Tri-colored LED indicates flat, sharp, or in tune. It's a perfect tool for improving your ear. A built-in click track/metronome has a naturally- sampled snare drum hit - there's no annoying buzz or tone. The Pocket Rockit's metronome has adjustable tempos between 60 -180 bpm provides a great way to work on your time.

C Tech Pocket Rockit V2 Guitar Headphone Amplifier Features:

• Plugs directly into your guitar no cables
• Built-in tuner and metronome
• 2 DSP effects engines provide reverb, delay, chorus, and flange effects (2 simultaneous)
• Models of vintage and current amplifier classics
• Analog front end
• Rotating input plug design (fits any guitar)

Most importantly, the Pocket Rockit sounds killer! Order today and practice big.

In a pinch for some phantom power?

The MP13 is an ideal single-mic preamp with clean phantom power and a crisp, full-frequency sound.

Rolls MP13 Mini-Mic Preamp Features:

• Single mic preamp
• XLR and 1/4" ins/outs
• +21V DC phantom power
• Clip LED indicator
• AC adapter included

Small and effective. Call or click to order now!

Powerful enough to blow the windows out of a doll house!

The Marshall MS-4 Micro Stack features 2 speaker cabs with a head, and it stands only 9-3/4" high. Includes fully functioning Gain, Volume, and Tone controls. The Marshall Micro Stack is powered by a 9V battery.

Marshall MS-4 Micro Stack Features:

• Smokin' stack design
• Screamin' stack sound
• Functional gain, volume, and tone controls

Here's a stack you don't need two roadies to carry. Put it in the cart.

Practice so quietly only you will know how good you're getting.

The Dean Bass in a Box Bass Headphone Amp lets you plug in your bass, put on the headphones, and start playing. You'll hear the coolest, punchiest bass tones you've ever heard. Has a flat/normal/bright selector.

Dean Bass in a Box Bass Headphone Amplifier Features:

• Includes headphones
• Has flat/normal/bright selector

This is the least costly way in the world to get great bass tone. Order today.

Compact and portable all-in-one Amp, Strap & Cable design!

Play anywhere, the amp is on the strap. The Mighty Moe Amp Strap offers you one of the hottest ideas in practice ampst: a guitar amp, strap, and cable all-in-one. Cool looks, comfortable, and built around an exclusive, U.S.-patented design. One of the most compact and portable guitar practice amp designs available.

Moe's Mighty Mission:
Mighty Moe adds to the player's creative range and offers total mobility in addition to the luxury of being able to play any time, anywhere. Mighty Moe is a light, small package with a mighty punch for musicians of all levels to use and enjoy.

Fun, Compact, Quick Set Up
Easily fits in any bag for easy storage and travel. Sets up in seconds.

Mighty Moe - A Ton of Fun!
At 11oz. the Mighty Moe is a comfortable and lightweight guitar practice amp with controls that are easy to get to.

Mighty Moe AmpStrap Specifications:

• Mighty Tone Amp with 3" Speaker in a Sleek Contoured Enclosure
• Hard-Wired Signal Cable fits any guitar
• Headphone Jack Cancels Speaker
• On/Off/Volume Dial
• Overdrive Intensity Dial
• LED On Indicator
• Weighs 11oz (.33 kg)
• Tote Bag Included

Mighty Moe AmpStrap Features:

• All-in-one: Amp, Strap & Cable
• Compact and Portable
• 9 Volt Battery Lasts Up to 9 Hours
• Clear & Overdrive Tone Controls
• Headphone Cancels Speaker
• Fits in a Guitar Bag
• Tote Bag Included

You really can take it with you! Order yours today.

In a pinch for some phantom power?

The MP13 is an ideal single-mic preamp with clean phantom power and a crisp, full-frequency sound.

Rolls MP13 Mini-Mic Preamp - Scratch 'n' Dent Features:

• Single mic preamp
• XLR and 1/4" ins/outs
• +21V DC phantom power
• Clip LED indicator
• AC adapter included

Small and effective. Call or click to order now!

The battery-powered Pocket Rock-It V1b Bass Headphone Amp allows you to practice silently in any location, and to have great tones at your disposal. The rotating input plug has 90 degrees of motion, so the V1 from C Tech can plug into any bass guitar jack-no cable needed!

The Pocket Rock-It Bass Headphone Amp's 2 "big" and 2 "tite" settings, with separate settings for active and passive pickup simulation give you tons of tone versatility. The Filter control is a continuously variable EQ that adjusts high and mid-range frequencies of the amp emulation model selected.

If you do decide to let the rest of the world in on your V1b headphone amp sessions, use the line out for recording or preamp applications. Jam with your CDs or MP3s with the line in or connect two Pocket Rock-Its and jam with a buddy (adapters and cables included).

The C Tech Pocket Rock-It V1b Bass Headphone Amp is designed, developed and engineered in the USA.

C Tech Pocket Rock-It V1b Bass Headphone Amp Features:

• Instrument Input: 1/4" male plug T/S
• Instrument Impedance: 1.0 M ohms
• CD/Line in: 1/8" jack T/R/S
• Line input impedance: >100 K ohms
• Line level input: 1.0 volts RMS
• Headphone/Line out: 1/8" jack T/R/S
• Headphone/Line out load: 8 Ohms min
• Battery (Alkaline or rechargeable): 9V
• Approx. Battery life: 10-15 hours
• Size: 3.3" x 2.3" x 1.4"
• Filter Control: 12db Mid/High Adjust
• Processor: 16 bit
• Headphones (included): 32 ohm, 44mm driver
• Also included: Stereo 1/8" (male) to dual 1/8" (female) headphone splitter, Stereo 1/8" (male) to stereo 1/4" (female) adapter, Stereo 1/8" (male) to stereo 1/8" (male) cable (6' long), Mono 1/4" (female) to mono 1/4" (female) adapter.

Plug in anywhere! Call or click today to order.