Vintage rock tones with modern features and high levels of gain!

The Marshall Vintage Modern 2466 Full-Stack includes the Vintage Modern 2466 Tube Amp Head, Vintage Modern 425A angled speaker cabinet and Vintage Modern 425B straight speaker cab.

The Marshall Vintage Modern 2466 Tube Amp Head is an all-valve amplifier with a choice of two dynamic ranges selectable by footswitch. The Low range equates equates to the performance you would come to expect from a stock vintage Marshall amplifier in terms of tone and available gain. The High range adds an extra preamp valve into the signal path, facilitating those classic hard rock tones of the seventies. Add to this the ability to dynamically interface with your instrument's Volume and Tone controls and the experience translates into a truly expressive and organic feel in performance.

Two frequency selective Pre-amp Volumes (Gains) - Body and Detail - facilitate greater flexibility in tone shaping for individual guitars and styles while the power amplifier is heavily influenced by the first Marshall guitar amplifiers to be produced, with four KT66 output valves yielding that substantial, fat and smooth tone. A MID Boost switch on the front panel fattens the tone even more while a traditional Marshall tone control circuit enables fine tuning of your sound.

A master volume has been included in order to practically manage the output levels at all venues. This is implemented after the phase splitter in order to fully exploit maximum preamp drive when the master is turned down low. A reverb level control mixes the on board plate reverb with the direct signal to whatever degree the player chooses. The reverb can be toggled on and off via the footswitch.

Finally, a series FX loop is provided for those players who wish to use outboard effects to further enhance their sound. Loop levels of 10dB and +4dB can be controlled via a rear panel switch as well as the option to completely bypass this feature if it is not required.

The cosmetics are also a carefully crafted hybrid of old and new styles made even more dramatic by the deep purple vinyl that covers the entire speaker series.

The Marshall Vintage Modern 425A angled cab and 425B straight cab are traditional Marshall 4 x 12 speaker enclosures in design. These cabs are mono/stereo switchable and are loaded with G12C 25 Watt Celestion Greenbacks. These were specifically developed for the Limited Edition Jimi Hendrix Super100JH stack and are voiced to give that rich and balanced harmonic timbre that complements vintage tone and the Vintage Modern Series perfectly.

The cosmetics are also a carefully crafted hybrid of old and new styles made even more dramatic by the deep purple vinyl that covers the entire series.

Marshall 2466, 425A, and 425B Full Stack Specifications:

• Head Dimensions: 29-1/2" x 12" x 9" (750 x 310 x 230 mm)
• Weight: 49.6 lbs (22.5 kg)
  
  Cabinet
• Impedance
• Mono 16 Ohms/4 Ohms
• Stereo 8 Ohms/8 Ohms
• Dimensions 30.5" x 30" x 14.5" (770 x 755 x 365 mm)
• Weight
• 425A: 79 lbs. (36 kg)
• 425B: 81.5 lbs (37 kg)

Marshall 2466, 425A, and 425B Full Stack Features:

• 100-Watt valve head
• Valve compliment: 4 x ECC83 (12AX7s) in preamp, 4 x KT66 in power amp
• Master Volume with two Gain Controls Detail (highs) & Body (lows)
• Two footswitchable Dynamic Ranges Low & High
• Mid Boost switch
• Footswitchable Proprietary digital Plate Reverb
• Series FX loop with level switch and bypass
• Made in England
  
  100-Watt, 4x12" cabinet
• Angled front
• Loaded with Celestion G12C 25 Greenbacks
• Mono or Stereo switchable
• 16 Ohms/4 Ohms mono
• 8 Ohms stereo
• Birch ply construction
• "finger-locking" joints
• Made in England

Few word combinations are as exciting as "Marshall stack"! Make it yours. Order today.