D.W. Fearn VT 1 Single Channel Vacuum Tube Microphone Preamp
Available from Musicians Friend
$2,400.00
on 11-12-2008
Larger Image
Enhanced View
Buy it Now!
With astounding transparency and warm, smooth presence.
The VT-series microphone preamplifiers will change the way you think of audio quality. The transparency is astounding. Vocals sound smoother, warmer, more intimate, with a compelling presence. Any microphone and any sound will benefit from the improved clarity, definition, and lack of solid-state artifacts. The VT-1 recreates the sound of classic tube preamps of the 1960s. Modern components and computer-optimized circuitry, unavailable during the vacuum tube era, elevate this design to a new level of performance.
In designing the VT-1, no compromise in sonic quality, reliability, or ruggedness were permitted. Like the best tube equipment of the 1950s and '60s, the VT-1 is built on a heavy-guage aluminum chassis, utilizing point-to-point wiring. Each vacuum tube is selected for minimum noise and microphonics, and maximum sonic clarity. The front panel switches control sealed, gold-contact precision relays for all audio switching, eliminating the possibility of dirty contacts degrading the sound and minimizing the internal audio path. Four class-A triode amplifier sections (in two tubes) in each channel comprise the entire active circuit. This surprisingly simple circuit, along with top-quality components and careful design optimization, results in the sonic superiority that the VT-1 has become known for. All over the globe, VT-1 preamps are in daily use in the world's best studios, as well as in home project studios, helping many top recording artists achieve the best possible sound.
D.W. Fearn VT-1 Single Channel Vacuum Tube Microphone Preamp Specifications:
- Input: 150 ohms
- Input Load Impedance: 1.5k ohms
- Minimum Input Level: -65 dBm nominal
- Maximum Input Level @ 20 cps: -30 dBm without pad, -5 dBm with 20 dB pad
- Gain: 53 dB
- Frequency Response: ±0.25 dB 20 cps to 20 kc; -3 dB @ 0.5 cps and 55 kc
- THD+Noise: less than 0.25% 20 cps to 20 kc
- Intermodulation Distortion: SMPTE less than 0.02%
- Signal to Noise Ratio: 74 dB minimum
- Equivalent Input Noise: -124 dBm maximum
- Output: low-Z, transformer-balanced
- Maximum Output Level: +22 dBm, 20k ohm load
- Power Requirements: 100, 120, or 220 VAC, 50/60 Hz
- Dimensions: 19" (48.26cm) W, 5.25" (13.34cm) H, 14" (35.56cm) D
- Weight: 18 lbs (8.16kg)
NOTE: Frequency is specified in cycles per second (cps) or kilocycles per second (kc). These units correspond to Hz and kHz respectively. Measurements made with -50 dBm input and 50 dB gain in a 22 cps to 22 kc bandwidth. Specifications and price subject to change without notice.
D.W. Fearn VT-1 Single Channel Vacuum Tube Microphone Preamp Features:
- All Vacuum-Tube Design
- Clean And Airy High End
- Fat Low End
- Unsurpassed Warmth, Transparency, And Musicality
- Lo-Z Input Position For Superior Performance With Transformerless Mics
- Phase (Polarity) Reverse Switch
- +48 Volt Phantom Power (Completely Disconnected When Off)
- Custom-Design Jensen Input And Output Transformers For Superb Sonics
- 20 Db Input Pad (Switchable)
- True Vu Meters (Amplifier Isolated)
- All Point-To-Point Audio Wiring
- High-Performance, Fully-Regulated Power Supplies With Exceptional Reserve
- Gold Input And Output Xlr Connectors
- Polypropylene And Polystyrene Coupling Capacitors
- All Audio Switching Through Gold-Contact, Sealed Precision Relays
- International Operation On 100, 120, Or 220 Vac, 50/60 Hz
- Ce Certified, Rohs-Compliant
- +4 Dbm Output - Conservatively Rated Precision Components And Rugged Construction For Stability And Long Life
- Line-Level Processing With The Lp-1 Line Padaccessory
Get professional recordings today!
|
D.W. Fearn VT 15 Vacuum Tube Recording Channel
Available from Musicians Friend
$4,950.00
on 11-12-2008
Larger Image
Enhanced View
Buy it Now!
A versatile studio tool that does it all!
The VT-15 Vacuum Tube Recording Channel combines the mic preamp from the D.W. Fearn VT-2, and the DI input functionality of the new VT-3, plus the acclaimed dynamics control of the VT-7 Compressor, and the most-often used features of the VT-4 Equalizer.
Mic Preamp
The mic preamp section has all the features of the VT-1 (the single-channel version of the VT-2), plus a built in Line Pad (the same as our LP-1), and a front-panel 1/4" jack for an instrument input from an electric or electronic guitar or keyboard.
Compressor
The compression section is identical to a single channel of the VT-7 Stereo Compressor, including a switchable high-pass filter in the sidechain to reduce low frequency compression when necessary.
Equalizer
The equalization section is a scaled-down version of the versatile VT-4 LC Equalizer. It has a single frequency for each of the LF Boost, LF Cut, HF Boost, and HF Cut. These frequencies were determined by analyzing which were the most often used settings on the VT-4. Approximate equalization frequencies: LF Boost 100Hz, shelving; LF Cut 90Hz,
shelving; HF Boost 9.8kHz, with adjustable Q; HF Cut 11kHz, shelving. The controls are continuously variable, from -12dB of cut to +12dB of boost. The HF Q is also continuously variable.
Which comes first, compression or equalization?
Sometimes you need the compression before the EQ, and sometimes the EQ should come first. The VT-15 does not lock you into only one configuration; a front panel switch allows you to instantly switch from Comp/EQ to EQ/Comp.
A full-size true VU meter monitors either gain reduction or output level. The mic/line input connector is a XLR female, and the output is a XLR male, both on the back panel. The Instrument input is a quarter-inch jack on the front panel. The VT-15 is in a standard rack-mount package, 5.25" high (3RU). A rear panel switch allows the VT-15 to instantly be converted from 120 to 240VAC operation, 50/60Hz.
D.W. Fearn VT-15 Vacuum Tube Recording Channel Specifications:
- Mic Input: 150 ohms
- Input Load Impedance: 1.5k ohms
- Minimum Input Level: -65 dBm nominal
- Maximum Input Level @ 20 cps: -30 dBm without pad, -5 dBm with 20 dB pad
- Instrument Input impedance: 1 Megohm
- Line Input Load Impedance: 40k ohms
- Maximum Line Input Level @ 20 cps: +25dBm (+35dBm with pad)
- Gain: <60 dB optimum (capable of 75dB)
- Frequency Response:± 0.25 dB 20 cps to 20 kc, ± 0.5 dB 11 cps to 28 kc, -3 dB @ 0.5 cps & 50 kc
- THD + Noise: <0.25% 20 cps to 20 kc
- Intermodulation Distortion SMPTE: <0.80%
- Signal to Noise Ratio: 72 dB typical operation
- Equivalent Input Noise: -124 dbm typical operation
- Output: low-Z, transformer balanced
- Maximum Output Level: +22 dBm unterminated
- Compression Range: up to 30dB
- Compression method: Pulse-width modulator
- Equalizer:
- Low-frequency Boost 100 cps, shelving
- Low-frequency Cut 80 cps, shelving
- High-frequency Boost 9.8 kc, peaking
- High-frequency Q 0.6 to 1.7
- High-frequency Cut
- 12 kc, shelving
- Power Requirements: 100, 120, or 220 VAC 50/60Hz, 50 W
- Dimensions: 19" (48.26cm) W x 5.25" (13.34cm) H x 9" (22.86cm) D
- Weight 18 lbs (8.16kg)
(specifications are preliminary and subject to change)
D.W. Fearn VT-15 Vacuum Tube Recording Channel Features:
- Mic Preamp/Compressor/Equalizer in one unit
- Instantly switch from Comp/EQ to EQ/Comp.
- Switchable high-pass filter in the sidechain
- All class-A triode vacuum tube audio path
- All controls are independent and can be used in any combination
- Constructed of heavy-gauge aluminum
- full-size true VU meter monitors
Get professional recordings today!
|
D.W. Fearn VT 2 Dual Channel Vacuum Tube Microphone Preamplifier
Available from Musicians Friend
$3,900.00
on 11-12-2008
Larger Image
Enhanced View
Buy it Now!
With astounding transparency and warm, smooth presence.
The VT-series microphone preamplifiers will change the way you think of audio quality. The transparency is astounding. Vocals sound smoother, warmer, more intimate, with a compelling presence. Any microphone and any sound will benefit from the improved clarity, definition, and lack of solid-state artifacts. The VT-2 recreates the sound of classic tube preamps of the 1960s. Modern components and computer-optimized circuitry, unavailable during the vacuum tube era, elevate this design to a new level of performance.
In designing the VT-2, no compromise in sonic quality, reliability, or ruggedness were permitted. Like the best tube equipment of the 1950s and '60s, the VT-2 is built on a heavy-guage aluminum chassis, utilizing point-to-point wiring. Each vacuum tube is selected for minimum noise and microphonics, and maximum sonic clarity. The front panel switches control sealed, gold-contact precision relays for all audio switching, eliminating the possibility of dirty contacts degrading the sound and minimizing the internal audio path. Four class-A triode amplifier sections (in two tubes) in each channel comprise the entire active circuit. This surprisingly simple circuit, along with top-quality components and careful design optimization, results in the sonic superiority that the VT-2 has become known for. All over the globe, VT-2 preamps are in daily use in the world's best studios, as well as in home project studios, helping many top recording artists achieve the best possible sound.
D.W. Fearn VT-2 Dual Channel Vacuum Tube Microphone Preamplifier Specifications:
- Input: 150 ohms
- Input Load Impedance: 1.5k ohms
- Minimum Input Level: -65 dBm nominal
- Maximum Input Level @ 20 cps: -30 dBm without pad, -5 dBm with 20 dB pad
- Gain: 53 dB
- Frequency Response: ±0.25 dB 20 cps to 20 kc; -3 dB @ 0.5 cps and 55 kc
- THD+Noise: less than 0.25% 20 cps to 20 kc
- Intermodulation Distortion: SMPTE less than 0.02%
- Signal to Noise Ratio: 74 dB minimum
- Equivalent Input Noise: -124 dBm maximum
- Output: low-Z, transformer-balanced
- Maximum Output Level: +22 dBm, 20k ohm load
- Power Requirements: 100, 120, or 220 VAC, 50/60 Hz
- Dimensions: 19" (48.26cm) W, 5.25" (13.34cm) H, 14" (35.56cm) D
- Weight: 18 lbs (8.16kg)
NOTE: Frequency is specified in cycles per second (cps) or kilocycles per second (kc). These units correspond to Hz and kHz respectively. Measurements made with -50 dBm input and 50 dB gain in a 22 cps to 22 kc bandwidth. Specifications and price subject to change without notice.
D.W. Fearn VT-2 Dual Channel Vacuum Tube Microphone Preamplifier Features:
- All Vacuum-Tube Design
- Clean And Airy High End
- Fat Low End
- Unsurpassed Warmth, Transparency, And Musicality
- Lo-Z Input Position For Superior Performance With Transformerless Mics
- Phase (Polarity) Reverse Switch
- +48 Volt Phantom Power (Completely Disconnected When Off)
- Custom-Design Jensen Input And Output Transformers For Superb Sonics
- 20 Db Input Pad (Switchable)
- True Vu Meters (Amplifier Isolated)
- All Point-To-Point Audio Wiring
- High-Performance, Fully-Regulated Power Supplies With Exceptional Reserve
- Gold Input And Output Xlr Connectors
- Polypropylene And Polystyrene Coupling Capacitors
- All Audio Switching Through Gold-Contact, Sealed Precision Relays
- International Operation On 100, 120, Or 220 Vac, 50/60 Hz
- Ce Certified, Rohs-Compliant
- +4 Dbm Output - Conservatively Rated Precision Components And Rugged Construction For Stability And Long Life
- Line-Level Processing With The Lp-1 Line Padaccessory - Single-Channel Version D.W. Fearn Vt-1 Also Available - Direct Recording Of Electric Instruments With The D.W. Fearn Vt-3 Vacuum Tube Di Or Pdb Passive Direct Box
Get professional recordings today!
|
D.W. Fearn VT 3 Dual Channel Vacuum Tube DI
Available from Musicians Friend
$2,100.00
on 11-12-2008
Larger Image
Enhanced View
Buy it Now!
Add depth, dynamics, and excitement to your recordings without adding noise!
The VT-3 is a dual-channel, all-triode vacuum tube DI ("direct box") for recording electric or electronic instruments. The inputs are designed to provide the proper load impedance for all instruments that have a 1/4-inch phone jack output. Tube circuitry provides the very high impedance necessary to capture all the details of these instruments.
The outputs of the VT-3 are mic level (150 ohm source impedance at a nominal -30dBV). The VT-3 is designed to operate into a high-quality microphone preamplifier like the Fearn VT-1 and VT-2 Vacuum Tube Microphone Preamplifiers.
Operation is very simple: plug the instrument into the 1/4" front panel jack and take the output either from the front panel XLR connector, or a parallel XLR connector on the back panel. A second 1/4" jack provides an output to feed a guitar amplifier when necessary. A ground-lift switch helps eliminate ground loop buzz, and a switchable high-pass filter gently rolls off frequencies below 100Hz when required.
The two channels are entirely independent and can be used with two different instruments at the same time.
D.W. Fearn VT-3 Dual Channel Vacuum Tube DI Specifications:
- Input: 200 mV nominal unbalanced
- Input Load Impedance: 1 megohm minimum
- Minimum Input Level: 5 mV nominal
- Maximum Input Level: 2.3 volts P-P for 1% THD
- Gain: -10 dB
- Frequency Response: ± 0.2 dB 10 cps to 20 kc, -3 dB @ 0.5 cps and 95 kc
- THD + Noise: <0.3% 20 cps to 20 kc
- Intermodulation Distortion: <0.01% SMPTE
- Noise: minimum 90 dB below output (22 cps to 22 kc bandwidth)
- Output Transformer Balanced (matches 150 ohm input)
- Output Level: -30 dBm nominal
- Maximum Output Level: -12 dBm @ 20 cps
- Crosstalk maximum: -90 dB @ 20 kc
- Power Requirements: 100/120/220 VAC 50/60Hz 25W
- Dimensions: 19"W x 5.25"H x 10"D, (48.3cm x 13.3cm x 25.4cm)
- Weight: 10 lbs (6.82 kg)
D.W. Fearn VT-3 Dual Channel Vacuum Tube DI Features:
- All-Triode Vacuum Tube DI
- Simple Operation
- Two Independent Channels
- Provides The Proper Load Impedance For All Instruments That Have A 1/4-Inch Phone Jack Output
- Ground-Lift Switch Helps Eliminate Ground Loop Buzz
- Switchable High-Pass Filter Gently Rolls Off Frequencies Below 100Hz
Get professional recordings today!
|
dbx 376 Tube Channel Strip
List Price: $649.95
Available from Musicians Friend
$529.95
on 11-12-2008
Larger Image
Enhanced View
Buy it Now!
The 376 adds more to make it an all-inclusive tool!
The dbx 376 Tube Channel Strip employs standard strip features, then adds more to make it an all-inclusive tool. The menu includes a tube preamp section, 3-band parametric EQ, compressor, de-esser, and digital outputs. Other features include a front panel instrument input, drive meter LEDs, threshold and de-esser meters, an eight-segment analog or digital meter, and a Type IV conversion system. Selectable sampling rates of 96, 88.2, 48, and 44.1kHz and 24, 20, and 16-bit word lengths add flexibility. Digital outputs include AES/EBU and S/PDIF. Word clock sync input and output are provided, and you can select dither and noise-shaping algorithms.
dbx 376 Tube Channel Strip Features:
- Tube microphone preamp
- 200V tube plate voltage
- Selectable mic/line switch
- +48 volt phantom power
- Three-band parametric EQ
- Compressor
- De-esser
- Front panel instrument input
- Drive meter LEDs
- Threshold and de-esser meters
- Eight-segment analog or digital meter
- Type IV conversion system
- Selectable sampling rates
- 24, 20, and 16-bit word lengths
- AES/EBU and S/PDIF digital outputs
- Selectable dither and noise-shaping algorithms
- Word clock sync input and output
Super-affordable price, super-powerful features. Order today.
|
dbx 386 Dual Vacuum Tube Preamp
List Price: $649.95
Available from Musicians Friend
$529.95
on 11-12-2008
Larger Image
Enhanced View
Buy it Now!
Brings the tube and digital worlds together in one affordable package!
The dbx 386 Dual-Vacuum Tube Preamp is a 2-channel microphone preamp with digital outs and the dbx Type IV conversion system. It features selectable 96, 88.2, 48, or 44.1kHz sampling rates, 24-, 20-, and 16-bit wordlengths, selectable dither and noise shaping, AES/EBU and S/PDIF digital outputs, word clock sync input and output, separate analog and digital output controls, 60dB of gain and +/- 15dB of output gain, a selectable mic/line switch, 48V phantom power, a 75Hz low cut filter, phase reverse, 12 segment LED, and a 20dB pad. With its impressive features, the dbx 386 lets you work in the digital world while retaining the indispensable warmth of analog.
Save BIG when you buy today!
|
EBS TD650 Tube Definition Bass Head
List Price: $2,299.00
Available from Musicians Friend
$1,839.00
on 11-12-2008
Larger Image
Enhanced View
Buy it Now!
Big watts and astounding versatility.
The EBS TD650 is a compact and powerful package, loaded with tube, solid state, and MOSFET technology. This no-compromise amp will satisfy every demand of the most versatile bass player.
The TD650 includes a 3-band equalizer with sweepable midrange, notch filter, compressor, bright filter, pure overdrive section and extras that include the unique EBS Phantom Power System, floating balanced XLR output, character filter, speaker simulator, line out and a serial/parallel effects loop. The overdrive section can be selected in tube or solid-state mode, employing either pure tube drive or solid-state tube emulation, to create your sound.
EBS TD650 Tube Definition Bass Head Specifications:
- Height: 3U / 13 cm
- Width: 19"
- Depth: 14"
- Weight: 27 lbs
EBS TD650 Tube Definition Bass Head Features:
- Switchable tube/solid State
- Drive control
- Unique tube suspension system
- Compressor/Limiter .
- Extremely powerful 4-band EQ
- Serial and parallel effects loop
- Floating balanced XLR output
- Built-in speaker simulator
- 9-volt EBS Phantom Power System
- Active intelligent cooling system
- 650W pure MOSFET power
It's a great head. Order today with the assurance of our 45-day lowest price and total satisfaction guarantees!
|
Eden DC210XLT 2x10 Metro Bass Combo Amp
List Price: $2,099.90
Available from Musicians Friend
$1,599.00
on 11-12-2008
Larger Image
Enhanced View
Buy it Now!
A fully professional 400W combo gig rig.
The Eden DC210XLT 2x10" Metro Bass Combo Amp has a dual channel preamp section that gives you the choice of tube or solid-state with full footswitch control. Each channel includes an independent effects loop. 400W drive a 4 ohm pair of 10" woofers and a horn. Other features of the Eden DC210XLT Combo include switchable automatic compression, 5-way semi-parametric tone control, an electronic crossover, stereo aux input, headphone out, tuner mute on footswitch, internal speaker on/off, and -12dB input pad. Includes dual function footswitch.
Eden DC210XLT 2x10 Metro Bass Combo Amp Specifications:
- 23"W x 24"H x 18-1/2"D
- 78 lbs.
Save BIG when you buy today!
|
Egnater Rebel 20 20W Tube Guitar Amp Head
Available from Musicians Friend
$599.99
on 11-12-2008
Larger Image
Enhanced View
Buy it Now!
Packed with cool and innovative features, the REBEL-20 doesn't just defy authority, it is the authority!
Sure it's small, but do not mistake it for a toy. The REBEL-20 is a truly professional amp with innovative features and a sound that is anything but small. Inside you'll find three GrooveTubes 12AX7 preamp tubes, a pair of GrooveTubes EL84 power tubes and a pair of GrooveTubes 6V6 power tubes. Not only do you get the signature Egnater TIGHT and BRIGHT voicing switches, you also have wide range gain control that lets you go from bluesy clean up to roaring high-gain lead all using a single gain knob.
The WATTS control lets you dial the power from 20 watts to 1 watt for bandstand to bedroom volume. The amp also includes a professional quality effects loop that doesn't "suck tone". But the coolest feature of the REBEL-20 is the TUBE MIX control — an Egnater first! With the TUBE MIX knob turned counterclockwise you get the classic American sound of the 6V6 power tubes. Set the knob full clockwise to experience the more aggressive, British sound of the EL84 tubes. For the first time, you can blend the two types of tubes in any proportion you wish to create a truly signature sound.
Egnater Products Rebel 20 20W Tube Guitar Amp Head Features:
- 20-Watt All-Tube Head
- Variable Wattage Control from 1w to 20w
- Tube Mix Blends Between 6V6 and EL84 Power Tubes
- Master Volume, Gain, Three Band EQ
- Egnater Signature Tight and Bright Voicing Switches
- Effects Loop
- Powered by Groove Tubes
- 100V/115V/230V Switchable
- Rugged Shoulder Bag Included
- Dimensions: 14.25 " (W) x 8.25 " (D) x 7.5" (H)
- Weight: 16 lb.
Tubes:
- Powered by GrooveTubes
- 3 x 12AX7
- 2 x 6V6
- 2 x EL84
You need sweet tone — get this amp head today!
|
|
Egnater Tourmaster Series 4100 100W All Tube Guitar Amp Head
Available from Musicians Friend
$1,399.99
on 11-12-2008
Larger Image
Enhanced View
Buy it Now!
Like four separate amps in one head.
Each of the Tourmaster 4100 amp head's channels has an identical set of controls, but that is where the similarities end.
Clean/Vintage 1 is the cleanest of the four. Within this channel lives a range of Classic tones ranging from pristine sparkle with the voicing switch set to MODERN to a punchy, aggressive drive (think clean JTM) in the CLASSIC mode. Pressing the button to activate the CONTOUR control opens an entire new range of beautiful clean, almost acoustic, tones not often found in a tube amplifier.
Clean/Vintage 2 has a very similar voicing to the Clean/Vintage 1 channel. This channel has more gain, so it can be pushed into mild overdrive. Sweet blues and classic rock tones are easily coaxed out of this channel. The contour knob adds another level of unique flavors.
Overdrive 1: From AC/DC crunch to modern rock, this channel covers a lot of bases all by itself. Dial down the gain and the feel is pure classic rock. Push the gain and enter into more modern, saturated territory. Scoop the mids with the CONTOUR control for monstrous metal or set it for classic British rhythm.
Overdrive 2: The Tourmaster's most intense channel, you'll find ferocious gain with a wide range of tones to suit the 80s shredder as well as the heaviest modern metal player. Scoop the mids with the powerful CONTOUR control for massive crunch or push the midrange for a solo tone that cuts through with serious authority.
Power Grid: This is a really cool feature you will only find on the Egnater Tourmaster amps. Using a group of 5 slide switches on the rear panel, you can set the power output for each channel individually. There is a 3-position slide switch corresponding to each of the four channels and a single FULL POWER/ HALF POWER slide switch. In FULL POWER mode, you can choose between 100w, 50w or 25w per channel. In the HALF POWER mode, you can between choose 50w, 25w or 10w per channel.
With the Tourmaster 4100 amp head, you not only have a wide array of tones available from the preamp channels, but with the Power Grid you can introduce any amount of power tube distortion you wish to each channel: all preset, all automatic.
Egnater Products Tourmaster Series 4100 100W All-Tube Guitar Amp Head Specifications:
- Output Power: 10 to 100 Watts RMS Presetable
- High Input Impedance: 1meg Ohm
- Low Input Impedance: 94k Ohms
- Output Impedance: 4 Ohms, 8 Ohms Or 16 Ohms - Selectable
- Effects Loop Send Impedance: 4k7 Ohms
- Effects Loop Return Impedance: 250k Ohms
- THD: 5% At Rated Output
- Preamp Tubes: Eight Selected Groovetubes / Egnater12AX7A / ECC83
- Output Tubes: Four Selected Groovetubes / Egnater 5881
- Density: +6db @ 120hz
- Presence: +8db @ 3.2khz
- Record Output Level: -50dBv To 0dBv
- Dimensions: 27.5" (W) x 11" (D) x 10.5 " (H)
- Weight: 60 lbs
Egnater Products Tourmaster Series 4100 100W All-Tube Guitar Amp Head Features:
- MAIN FEATURES
- 100-Watt All-Tube Head
- Four Channels with Selectable voicing
- Power Grid: Set Wattage for Each Channel
- from 10w up to 100w
- Tube-driven Assignable Effects Loop
- Tube Driven Reverb
- Rugged Six-Button Footswitch
- Powered by Groovetubes
FRONT PANEL
- Four independent channels each with: Gain control; Master control; Treble, middle, bass; Classic/modern voicing switch
- Tube driven reverb
- Master Presence/Density
REAR PANEL
- Assignable tube driven effects loop: Assign to channels 1&2, Assign to channels 3&4, Assign to all four channels, Assign to pedal only, Send and return level controls, Selectable series or parallel
- Cabinet voiced line/recording out
- Simple master bias adjust with test points
POWER GRID
- Six preset power output levels for each channel from 10 to 100 watts
- Full or half power switch
Call today to get a huge array of tube tones with the Tourmaster 4100.
|
More Items 1 2 3 4 5 6 7 8 9 10 Next
GuitarPeddler Home
Guitar Links
NOTICE : All prices, availability, and specifications are subject to verification by their respective retailers.
Privacy Policy
Copyright © 2008 Dominant Systems Corporation
info@guitarpeddler.com
Last Modified : 11-12-2008
|
|
|
