The Markbass Micromark bass combo is an amplifier that is less than 9" in any direction. Despite only a 6" speaker, the Micromark is a practice amp with deceptively loud volume and the kind of sound quality you'd expect from a B&C speaker with Markbass electronics. Pumping out 50W of power, the Micromark amp boasts a mini-plug for attaching your CD or MP3 players, to help you master your favorite licks.

The Markbass Micromark amp has a Variable Pre-shape filter for boosting lows around 35Hz and highs around 10kHz, and cutting mids at 380H-which is perfect for rockers and slap bassists alike. There's a volume control knob, headphone jack, XlR output for recording and live situations, a ground lift to eliminate hum, and a 1/4" jack tweeter out for the optional Markbass satellite tweeter.

Markbass Micromark 50W 1x6 Bass Combo Amp Specifications:

• Speaker: 1 x 6"
• Tweeter: optional "sattelite tweeter, not included
• Impedance: 8 ohms
• Speaker power handling: 50W RMS (AES Standard)
• Sensitivity: 100 db SPL
• Frequency response: 70Hz to 8kHz
• Crossover Frequency: 3.5kHz
• Dimensions: 8.86"W x 8.86"H x 8.62"D
• Weight: 9.26 lbs.

Markbass Micromark 50W 1x6 Bass Combo Amp Features:

• 6" B&C speaker
• Mini-plug aux in (for CD or MP3 player)
• Mini-plug headphone jack
• Volume level control
• Variable Pre-shape filter
• XLR line out
• Ground lift
• Speaker off switch
• Tweeter jack for optional "sattelite" tweeter
• Grill for protecting speaker
• Handle on top for transportation
• Dual-sided fiberglass PC boards with lined perforations for high-quality solder connections
• Surface-mount components are silicon-sealed to isolate vibrations
• Computer-grade pre-assembled ribbon connector cable harnesses and ribbons for noise-free operation
• Integrated threaded posts for easy assembly/disassembly and added durability
• Rigid 2mm thick aluminium chassis for a long-lasting finish

It's true that practice makes perfect. So order this little amp and polish up your game.

The Markbass Mini CMD 121P is a bass combo amplifier that gives you fat sound with electric or acoustic basses. That makes the Mini CMD 121P amp perfect for rehearsal studios or small club applications. The Markbass Mini CMD 121P comes with a built-in Little Mark II bass head in the top rear area. Bassists will appreciate the Markbass-designed Vintage Loudspeaker Emulator and Variable Pre-shape Filter which help give this Mini CMD a warm natural sound. The Little Mark II also has a Neutrik Speakon combo jack output that accepts both Speakon or 1/4" speaker cable as well as a second 1/4" speaker out jack so you can hook up to another 8 ohm cab for a 500W rig. You'll also find a balanced XLR out, unbalanced tuner out so you can tune as you play without passing your signal through pedals. A Send and Return Effect loop protects you from losing your signal if one of your pedals dies or a cable in the chain gives out.

Markbass Mini CMD 121P 1x12 Bass Combo Amp Specifications:

• Impedance: 8 ohms
• Speaker power handling: 400W RMS (AES Standard)
• Frequency Response: 45Hz to 18kHz
• Crossover Frequency: 3.5kHz
• Sensitivity: 99dB SPL
• Weight: 29.3 lbs.
• Dimensions: 15.3"(W) x 17"(H) x 14.1"(D)
  
  Little Mark II head

Markbass Mini CMD 121P 1x12 Bass Combo Amp Features:

• Solid state preamp
• 12" B&C speaker
• Piezo tweeter
• Rear bass reflex
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Lightweight for easy transport
• Handle on top for transporting
• Protected corners
• Grill screen to protect speaker
  
  Little Mark II
• Provides 500W at 4 ohm or 300W at 8 ohm
• Gain and Master volume controls
• Clip warning light
• EQ includes controls for Low, Mid Frequency Low, High Frequency Low, and High
• VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters
• Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
• Balanced XLR out
• Ground lift switch to eliminate hum
• Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
• Send and Return Effect ensures main signal continues even if something dies in your effects chain

Big sound in a small package. What more could you want? Order today!

The Markbass CMD 151P is a bass combo amplifier equipped with Markbass' flagship solid state preamp, the Little Mark II. Despite being a Mini model, the CMD 151P amp gives you maximum power and sound. The amp provides plenty of power to blow through the high-quality 15" B&C woofer and piezo tweeter. The CMD 151P also has 2 speaker outs which allow you to hook up to another 8 ohm extension cab, giving you a 500W rig! The Little Mark II has a 4-band EQ, as well as two exclusive Markbass' filters for rounding out your tone to perfection. A handle on top makes Markbass CMD 151P amp easy to transport too.

Markbass Mini CMD 151P 300/500W 1x15 Bass Combo Amp Specifications:

• Speaker: 1 x 15"
• Tweeter: piezo
• Bass reflex: rear
• Impedance: 8 ohms
• Sensitivity: 100 dB SPL
• Speaker power handling: 400W RMS (AES Standard)
• Frequency response: 40Hz to 18kHz
• Crossover Frequency: 3.5kHz
• Dimensions: 18.27"W x 18.27"H x 18.9"D
• Weight: 40.79 lbs.
  
  Little Mark II head
• Power
• Input impedance: 500Kohm, max. voltage: 15 Vpp
• Balanced Output (XLR): 22Kohm, max. voltage 25 Vpp
• Effect Return impedance: 22Kohm, max. voltage: 25 Vpp
• Output Power: 300W RMS at 8 ohm, 500W RMS at 4 ohm
• Power requirement: 100/120V; 230V; 240V; 50/60Hz
• Controls
• GAIN 80 dB to +23 dB range
• MASTER VOLUME
• GROUND LIFT: switch on rear panel
• Equalization
• LOW
• Center frequency: 40Hz; level ±16dB
• LOW MID
• Center frequency 360Hz, level ±16dB
• HIGH MID
• Center frequency 800Hz, level ±16dB
• HIGH
• 10kHz shelf; level ±16dB
• VPF (Variable Pre-shape Filter)
• center frequency 380Hz (cut)
• VLE (Vintage Loudspeaker Emulator)
• frequency range 250Hz 20kHz (cut)
• Outputs
• EFFECT SEND
• Unbalanced, max. voltage 20 Vpp (pre-EQ)
• TUNER OUT
• Unbalanced, max. voltage 25 Vpp
• LINE OUT
• Balanced XLR, max. voltage 10 Vpp
• SPEAKER OUT
• Speakon, 1/4"

Markbass Mini CMD 151P 300/500W 1x15 Bass Combo Amp Features:

• Built-in Little Mark II solid state preamp on top rear
• 15" B&C woofer
• Piezo tweeter
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Top handle for transportation
• Grill for protecting speaker
• Lightweight
  
  Little Mark II
• Provides 500W at 4 ohm or 300W at 8 ohm
• Gain and Master volume controls
• Clip warning light
• EQ includes controls for Low, Mid Frequency Low, High Frequency Low, and High
• VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters
• Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
• Balanced XLR out
• Ground lift switch to eliminate hum
• Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
• Send and Return Effect ensures main signal continues even if something dies in your effects chain

Don't be fooled by the size and weight of this compact combo. It's sound is bigger than you think. Order today!

The Markbass Minimark Bass Combo Amp with its astonishing volume, is a brilliant choice for rehearsing, practicing, and teaching. The Micromark amplifier's big brother, the Minimark sports two 6" custom B&C neodymium woofers and an onboard piezo tweeter. The Markbass Minimark amp cranks out an incredible 250W of power when used with an extension cab (or 150W on its own). The Minimark amp is even strong enough for you to use on gigs. The compact amp section includes level control, VLE and VPF filters, aux in, headphone out, speaker on/off switch, and balanced XLR line out. The Markbass Minimark combo amp's incredibly small size and weight mean you can even take this bass combo with you to a gig on public transportation.

Markbass Minimark 150/250W 2x6 Bass Combo Amp Specifications:

• Impedance: 8 ohm
• Speaker size: 2 x 6"
• Reflex: rear
• Tweeter: Piezo Tweeter
• Cab Power Handling: 300W RMS (AES Standard)
• Power Supply: Special Markbass digital power supply
• Crossover Frequency: 3.5kHz
• Power amp output: 150W 8 ohm / 250W 4 ohm
• Frequency Response: 59Hz to 18kHz
• Sensitivity: 101 dB SPL
• Weight: 20.72 lbs.
• Dimensions: 8.86"W x 17.24"H x 15.24"D

Markbass Minimark 150/250W 2x6 Bass Combo Amp Features:

• Solid state preamp
• Analog power amp
• B&C neodymium woofers
• Piezo tweeter
  
  Rear panel:
• Level control
• Vintage Loudspeaker Emulator and Variable Pre-shape filters
• Aux in
• Headphone out
• Speaker on/off switch Balanced XLR line out
  
  Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Grill for protecting speakers
• Lightweight
• Handle on top for carrying

When you need some on-the-go muscle, let this 2 x 6" combo flex it's power. Order today!

The Markbass R500 is a bass amplifier head that will have you rocking out old-school, rocking hard, creating your own alternative rock, or shredding up the stage stealing the spotlight from your guitarists! The 500W analog R500 amp (at 4 ohms; 300W at 8 ohms) features a tube preamp that will break up just the way you want it to, and a newly designed limiter that produces glorious distortion instead of cramping your style. The simple 4-band EQ gives you all you need to access a wide range of sounds for any genre. As far as controls, the Gain knob is for the amount of tube overdrive, whereas the Master knob is for your volume.

Markbass R500 500W Bass Amp Head Specifications:

• Power
• Input impedance: 500Kohm, max. voltage: 9 Vpp
• Effect Return impedance: 33Kohm, max. voltage: 12 Vpp
• Output Power: 300W RMS at 8 ohms, 500W RMS at 4 ohms
• Power Requirement: 100V; 120V; 230V; 240V; 50/60Hz
  
  Controls
• GAIN: 80dB to +25dB range
• GROUND LIFT: Switch on rear panel
• MASTER VOLUME
• Optional footswitch: mute
  
  Equalization
• LOW
• Center frequency: 80Hz; level ±12dB
• LOW MID
• Center frequency 400Hz, level ±12dB
• HIGH MID
• Center frequency 800Hz, level ±12dB
• HIGH
• 3kHz shelf; level ±12dB
  
  Outputs
• EFFECT SEND
• Unbalanced, max. voltage 12 Vpp (pre-EQ)
• TUNER OUT
• Unbalanced, max. voltage 2 Vpp
• LINE OUT
• Balanced XLR, max. voltage 25 Vpp
• SPEAKER OUT
• Speakon, 1/4" x 2
  
  Other
• Dimensions: 8.16"(W) x 3.39"(H) x 11.89"(D)
• Weight: 8.16 lbs.

Markbass R500 500W Bass Amp Head Features:

• Analog amp with a tube preamp which provides 500W at 4 ohms; 300W at 8 ohms
• 1/4" input jack works with passive or active basses
• Gain knob controls tube overdrive
• Master knob controls volume
• Line out controls rear XLR line out volume level
• 4-band EQ: Low, Low Mid, High Mid, HIgh
• Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
• Balanced XLR line out
• Pre EQ/Post EQ switch to determine whether the output signal is effected by the EQ settings or not
• Ground lift switch to eliminate hum
• Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
• Send and Return Effect ensures main signal continues even if something dies in your effects chain
• Dual-sided fiberglass PC boards with lined perforations for high-quality solder connections
• Surface-mount components are silicon-sealed to isolate vibrations
• Computer-grade pre-assembled ribbon connector cable harnesses and ribbons for noise-free operation
• Integrated threaded posts for easy assembly/disassembly and added durability
• Rigid 2mm thick aluminium chassis for a long-lasting finish

Increase the power and tonal versatility of your bass sound with this top-quality 500W bass head. Get yours today!

These Markbass rack ears are specifically designed for use with the Markbass F1 bass amp head. 2-piece set allows you to mount your amplifier into one unit of any standard rack case.

Markbass Rack Ear Kit for F1 Features:

• Two mounting brackets

Save on these brackets, order today!

These Markbass rackears are specifically designed for use with the Markbass Little Mark 250 or Little Mark II bass amp heads. This 2-piece rack ear kit allows you to mount either amplifier into one unit of any standard rack case.

Markbass Rack Ear Kit for Little Mark 250 and Little Mark II Features:

• Left and right mounting brackets

Order your mounting kit today!

The SA450 is Markbass' standard, solid-state, analog powered professional head. Versatile and packed with plenty of features as listed below, it provides more EQ control than its sibling the Little Mark II, a line out level control and pre/post EQ switch. Add this bass amp head to your rig and listen to the difference it makes in your overall stage presence.

Markbass SA450 500W Bass Head Specifications:

• Power
• Input impedance: 500 Kohm, max. voltage: 9 Vpp
• Effect return impedance: 33 Kohm, max. voltage: 12 Vpp
• Output Power: 300W RMS at 8 ohms, 500W RMS at 4 ohms
• Power Requirement: 100/120V; 230V; 240V; 50/60Hz
  
  Controls
• GAIN: 80dB to +25dB range
• LINE OUT: Level control on front panel
• PRE/POST EQ (for line out): Switch on rear panel
• GROUND LIFT: Switch on rear panel
• MASTER VOLUME
  
  Equalization
• LOW
• Center frequency: 40Hz; level ±16dB
• LOW-MID
• Semi-parametric: frequency 100 800Hz, level ±16dB
• HIGH-MID
• Semi-parametric: frequency 700Hz 6kHz, level ±16dB
• HIGH
• 10kHz shelf; level ±16dB
• VPF (Variable Pre-shape Filter)
• Center frequency: 380Hz (cut)
• VLE (Vintage Loudspeaker Emulator)
• 250Hz 20kHz cut
  
  Outputs
• EFFECT SEND
• Unbalanced, max. voltage 12 Vpp (pre-EQ)
• TUNER OUT
• Unbalanced, max. voltage 2 Vpp
• LINE OUT
• Balanced XLR, max. voltage 25 Vpp
• SPEAKER OUT
• Speakon, 1/4"
  
  Other
• Dimensions: 14.5"(W) x 3.39"(H) x 11.9"(D)
• 2U tall
• 19"(W) with rack ears
• Weight: 7.5lbs.

Markbass SA450 500W Bass Head Features:

• Soild state analog power preamp
• Provides 500W to a 4 ohm cab, 300W to a 8 ohm cab
• 1/4" input jack works with both passive and active basses
• Gain and Master volume controls
• Clip warning light
• Line out volume control knob
• EQ includes controls for Low, Mid Frequency Low, High Frequency Low, and High
• High and Low level controls for deciding how much frequency area will be affected by the EQ
• VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters
• Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
• Balanced XLR out
• Pre EQ/Post EQ switch to determine whether the output signal is effected by the EQ settings or not
• Ground lift switch to eliminate hum
• Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
• Send and Return Effect ensures main signal continues even if something dies in your effects chain
• Dual-sided fiberglass PC boards with lined perforations for high-quality solder connections
• Surface-mount components are silicon-sealed to isolate vibrations
• Computer-grade pre-assembled ribbon connector cable harnesses and ribbons for noise-free operation
• Integrated threaded posts for easy assembly/disassembly and added durability
• Rigid 2mm thick aluminium chassis for a long-lasting finish

See what this excellent bass head does to your amp and overall bass sound. Order today!

The SA450 is Markbass' standard, solid-state, analog powered professional head. Versatile and packed with plenty of features as listed below, it provides more EQ control than its sibling the Little Mark II, a line out level control and pre/post EQ switch. Add this bass amp head to your rig and listen to the difference it makes in your overall stage presence.

Markbass SA450 500W Bass Head - Scratch 'n' Dent Specifications:

• Power
• Input impedance: 500 Kohm, max. voltage: 9 Vpp
• Effect return impedance: 33 Kohm, max. voltage: 12 Vpp
• Output Power: 300W RMS at 8 ohms, 500W RMS at 4 ohms
• Power Requirement: 100/120V; 230V; 240V; 50/60Hz
  
  Controls
• GAIN: 80dB to +25dB range
• LINE OUT: Level control on front panel
• PRE/POST EQ (for line out): Switch on rear panel
• GROUND LIFT: Switch on rear panel
• MASTER VOLUME
  
  Equalization
• LOW
• Center frequency: 40Hz; level ±16dB
• LOW-MID
• Semi-parametric: frequency 100 800Hz, level ±16dB
• HIGH-MID
• Semi-parametric: frequency 700Hz 6kHz, level ±16dB
• HIGH
• 10kHz shelf; level ±16dB
• VPF (Variable Pre-shape Filter)
• Center frequency: 380Hz (cut)
• VLE (Vintage Loudspeaker Emulator)
• 250Hz 20kHz cut
  
  Outputs
• EFFECT SEND
• Unbalanced, max. voltage 12 Vpp (pre-EQ)
• TUNER OUT
• Unbalanced, max. voltage 2 Vpp
• LINE OUT
• Balanced XLR, max. voltage 25 Vpp
• SPEAKER OUT
• Speakon, 1/4"
  
  Other
• Dimensions: 14.5"(W) x 3.39"(H) x 11.9"(D)
• 2U tall
• 19"(W) with rack ears
• Weight: 7.5lbs.

Markbass SA450 500W Bass Head - Scratch 'n' Dent Features:

• Soild state analog power preamp
• Provides 500W to a 4 ohm cab, 300W to a 8 ohm cab
• 1/4" input jack works with both passive and active basses
• Gain and Master volume controls
• Clip warning light
• Line out volume control knob
• EQ includes controls for Low, Mid Frequency Low, High Frequency Low, and High
• High and Low level controls for deciding how much frequency area will be affected by the EQ
• VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters
• Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
• Balanced XLR out
• Pre EQ/Post EQ switch to determine whether the output signal is effected by the EQ settings or not
• Ground lift switch to eliminate hum
• Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
• Send and Return Effect ensures main signal continues even if something dies in your effects chain
• Dual-sided fiberglass PC boards with lined perforations for high-quality solder connections
• Surface-mount components are silicon-sealed to isolate vibrations
• Computer-grade pre-assembled ribbon connector cable harnesses and ribbons for noise-free operation
• Integrated threaded posts for easy assembly/disassembly and added durability
• Rigid 2mm thick aluminium chassis for a long-lasting finish

See what this excellent bass head does to your amp and overall bass sound. Order today!

The Markbass SD800 amp head is perfect for the times when you need speed and clarity at high volumes, especially in big-stage applications. This digital power amp delivers 750W of power into a 4 ohm cab or 450W into an 8 ohm cab. Recommended for use with big cabinets (8X10, 6X10, or 2X15), or two-cabinet rigs, this little solid-state head gives you plenty of headroom and has several options for protecting and shaping your sound, from its VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) options to the Pre/Post EQ setting which allows you to choose whether your line out signal is affected by the amp's EQ. The SD800 Head has an input jack that can be used with either active or passive basses as well as dual Neutrik Speakon Combo jacks so you can connect to one or two speaker cabs using 1/4" speaker cables or Speakon cables.

Markbass SD800 750W Bass Head Specifications:

• Power
• Input impedance: 500Kohm, max. voltage: 9 Vpp
• Effect return impedance: 33Kohm, max. voltage: 12 Vpp
• Output Power: 450W RMS at 8 ohms, 750W RMS at 4 ohms
• Power Requirement: 100/120V; 230V; 240V; 50/60Hz
  
  Controls
• GAIN: 80dB to +25dB range
• LINE OUT: level control on front panel
• PRE/POST EQ (for line out): switch on rear panel
• GROUND LIFT: switch on rear panel
• MASTER VOLUME
  
  Equalization
• LOW
• Center frequency: 40 Hz; level ±16dB
• LOW-MID
• Semi-parametric: frequency 100 800 Hz, level ±16dB
• HIGH-MID
• Semi-parametric: frequency 700 Hz 6 kHz, level ±16dB
• HIGH
• 10kHz shelf; level ±16dB
• VPF (Variable Pre-shape Filter)
• Center frequency: 380Hz (cut)
• VLE (Vintage Loudspeaker Emulator)
• 250Hz 20kHz cut
  
  Outputs
• EFFECT SEND
• Unbalanced, max. voltage 12 Vpp (pre-EQ)
• TUNER OUT
• Unbalanced, max. voltage 2 Vpp
• LINE OUT
• Balanced XLR, max. voltage 25 Vpp
• SPEAKER OUT
• Speakon, 1/4"
  
  Other
• Dimensions: 14.5"(W) x 3.39"(H) x 11.9"(D)
• 2U tall
• 19"(W) with rack ears
• Weight: 7.5lbs.

Markbass SD800 750W Bass Head Features:

• Solid state digital power preamp
• Delivers 750W of power into a 4 ohm cab, 450W into an 8 ohm cab
• 1/4" input jack works with active or passive basses
• Gain and master knobs
• XLR line out
• Vintage Loudspeaker Emulator filters out high frequencies
• Variable Pre-shape Filter boosts lows (around 35Hz and highs (around 10kHz), and cuts mids at 380Hz
• Dual Neutrik Speakon Combo jacks allows it to be connected to one or two speaker cabs using 1/4" speaker cables or Speakon cables
• Two balanced XLR output
• Pre/Post EQ switch to determine whether signal is affected by EQ settings or not
• Ground lift button for eliminating hum from grounding problems
• Unbalanced tuner out lets you tune as you play without passing your signal through your pedals
• Send Effect and Return Effect means you won't lose signal if something in your effects chain dies while playing
• Dual-sided fiberglass PC boards with lined perforations for high-quality solder connections
• Surface-mount components are silicon-sealed to isolate vibrations
• Computer-grade pre-assembled ribbon connector cable harnesses and ribbons for noise-free operation
• Integrated threaded posts for easy assembly/disassembly and added durability
• Rigid 2mm thick aluminium chassis for a long-lasting finish
  
  

Power up with this hearty digital power preamp and listen as your music takes off to new heights. Order one today!

The Markbass SD800 amp head is perfect for the times when you need speed and clarity at high volumes, especially in big-stage applications. This digital power amp delivers 750W of power into a 4 ohm cab or 450W into an 8 ohm cab. Recommended for use with big cabinets (8X10, 6X10, or 2X15), or two-cabinet rigs, this little solid-state head gives you plenty of headroom and has several options for protecting and shaping your sound, from its VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) options to the Pre/Post EQ setting which allows you to choose whether your line out signal is affected by the amp's EQ. The SD800 Head has an input jack that can be used with either active or passive basses as well as dual Neutrik Speakon Combo jacks so you can connect to one or two speaker cabs using 1/4" speaker cables or Speakon cables.

Markbass SD800 750W Bass Head - Scratch 'n' Dent Specifications:

• Power
• Input impedance: 500Kohm, max. voltage: 9 Vpp
• Effect return impedance: 33Kohm, max. voltage: 12 Vpp
• Output Power: 450W RMS at 8 ohms, 750W RMS at 4 ohms
• Power Requirement: 100/120V; 230V; 240V; 50/60Hz
  
  Controls
• GAIN: 80dB to +25dB range
• LINE OUT: level control on front panel
• PRE/POST EQ (for line out): switch on rear panel
• GROUND LIFT: switch on rear panel
• MASTER VOLUME
  
  Equalization
• LOW
• Center frequency: 40 Hz; level ±16dB
• LOW-MID
• Semi-parametric: frequency 100 800 Hz, level ±16dB
• HIGH-MID
• Semi-parametric: frequency 700 Hz 6 kHz, level ±16dB
• HIGH
• 10kHz shelf; level ±16dB
• VPF (Variable Pre-shape Filter)
• Center frequency: 380Hz (cut)
• VLE (Vintage Loudspeaker Emulator)
• 250Hz 20kHz cut
  
  Outputs
• EFFECT SEND
• Unbalanced, max. voltage 12 Vpp (pre-EQ)
• TUNER OUT
• Unbalanced, max. voltage 2 Vpp
• LINE OUT
• Balanced XLR, max. voltage 25 Vpp
• SPEAKER OUT
• Speakon, 1/4"
  
  Other
• Dimensions: 14.5"(W) x 3.39"(H) x 11.9"(D)
• 2U tall
• 19"(W) with rack ears
• Weight: 7.5lbs.

Markbass SD800 750W Bass Head - Scratch 'n' Dent Features:

• Solid state digital power preamp
• Delivers 750W of power into a 4 ohm cab, 450W into an 8 ohm cab
• 1/4" input jack works with active or passive basses
• Gain and master knobs
• XLR line out
• Vintage Loudspeaker Emulator filters out high frequencies
• Variable Pre-shape Filter boosts lows (around 35Hz and highs (around 10kHz), and cuts mids at 380Hz
• Dual Neutrik Speakon Combo jacks allows it to be connected to one or two speaker cabs using 1/4" speaker cables or Speakon cables
• Two balanced XLR output
• Pre/Post EQ switch to determine whether signal is affected by EQ settings or not
• Ground lift button for eliminating hum from grounding problems
• Unbalanced tuner out lets you tune as you play without passing your signal through your pedals
• Send Effect and Return Effect means you won't lose signal if something in your effects chain dies while playing
• Dual-sided fiberglass PC boards with lined perforations for high-quality solder connections
• Surface-mount components are silicon-sealed to isolate vibrations
• Computer-grade pre-assembled ribbon connector cable harnesses and ribbons for noise-free operation
• Integrated threaded posts for easy assembly/disassembly and added durability
• Rigid 2mm thick aluminium chassis for a long-lasting finish
  
  

Power up with this hearty digital power preamp and listen as your music takes off to new heights. Order one today!

The Markbass Standard 102HF bass speaker cabinet is recommended for bass players who need a smaller pro-sounding rig. For those who like to combine cabinets, add a 102HF to a Markbass Standard 151HF for even more impact. Using 2 102HF bass cabs together works beautifully with a stereo power amp. Rated at 400W RMS, the small Standard 102HF cab packs an impressive punch for its size. The 102HF bass speaker cabinet features stylish woofers designed as part of a collaboration between Markbass and B&C Speakers.

Markbass Standard 102HF Front-Ported Neo 2x10 Bass Speaker Cabinet Specifications:

• Impedance: 8 or 4 ohms
• Bass ports: front
• Tweeter: 1" compression driver with custom horn
• Power Handling: 400W RMS (AES Standard)
• Crossover Frequency: 3.5 kHz
• Frequency Response: 40Hz to 20kHz
• Sensitivity: 101 dB SPL
• Weight: 49.8 lbs.
• Dimensions: 23.4"W x 21.6"H x 18.9"D

Markbass Standard 102HF Front-Ported Neo 2x10 Bass Speaker Cabinet Features:

• 2 x 10" speakers
• Front reflex enclosure
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Lightweight

Let your bass be heard with this solid 2 x 10" cab. Order today.

The Markbass Standard 102HF bass speaker cabinet is recommended for bass players who need a smaller pro-sounding rig. For those who like to combine cabinets, add a 102HF to a Markbass Standard 151HF for even more impact. Using 2 102HF bass cabs together works beautifully with a stereo power amp. Rated at 400W RMS, the small Standard 102HF cab packs an impressive punch for its size. The 102HF bass speaker cabinet features stylish woofers designed as part of a collaboration between Markbass and B&C Speakers.

Markbass Standard 102HF Front-Ported Neo 2x10 Bass Speaker Cabinet - Scratch 'n' Dent Specifications:

• Impedance: 8 or 4 ohms
• Bass ports: front
• Tweeter: 1" compression driver with custom horn
• Power Handling: 400W RMS (AES Standard)
• Crossover Frequency: 3.5 kHz
• Frequency Response: 40Hz to 20kHz
• Sensitivity: 101 dB SPL
• Weight: 49.8 lbs.
• Dimensions: 23.4"W x 21.6"H x 18.9"D

Markbass Standard 102HF Front-Ported Neo 2x10 Bass Speaker Cabinet - Scratch 'n' Dent Features:

• 2 x 10" speakers
• Front reflex enclosure
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Lightweight

Let your bass be heard with this solid 2 x 10" cab. Order today.

The Markbass Standard 104HF bass cab features the power of ultra-light neodymium B&C speakers to give you a great power-to-weight ratio. So while the Standard 104HF pumps out plenty of sound, it's not a behemoth to carry around. The four 10" woofers surround the 1" HF compression driver with custom horn tweeter. The Standard 104HF bass cab is made of high-grade, multi-ply poplar manufactured to maximize sound quality. Protective corners and a grill protect the Markbass Standard 104HF when you're between shows.

Markbass Standard 104HF Front-Ported Neo 4x10 Bass Speaker Cabinet Specifications:

• Impedance: 8 or 4 ohms
• Speaker size: 4 x 10"
• Bass ports: front
• Tweeter: 1" compression driver with custom horn
• Power Handling: 800W RMS (AES Standard)
• Crossover Frequency: 3.5kHz
• Frequency Response: 35Hz to 20kHz
• Amp output power
• (analog) 250W at 4 ohm / 150W at 8 ohm
• Sensitivity: 103 dB SPL
• Weight: 65.92 lbs.
• Dimensions: 23.39"W x 29.13"H x 18.9"D

Markbass Standard 104HF Front-Ported Neo 4x10 Bass Speaker Cabinet Features:

• Ultra-light neodymium B&C speakers
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Grill for protecting speakers
• Lightweight

This solid cab will give your bass a more "in your face" feel. Order one today.

The Markbass Standard 104HF bass cab features the power of ultra-light neodymium B&C speakers to give you a great power-to-weight ratio. So while the Standard 104HF pumps out plenty of sound, it's not a behemoth to carry around. The four 10" woofers surround the 1" HF compression driver with custom horn tweeter. The Standard 104HF bass cab is made of high-grade, multi-ply poplar manufactured to maximize sound quality. Protective corners and a grill protect the Markbass Standard 104HF when you're between shows.

Markbass Standard 104HF Front-Ported Neo 4x10 Bass Speaker Cabinet - Scratch 'n' Dent Specifications:

• Impedance: 8 or 4 ohms
• Speaker size: 4 x 10"
• Bass ports: front
• Tweeter: 1" compression driver with custom horn
• Power Handling: 800W RMS (AES Standard)
• Crossover Frequency: 3.5kHz
• Frequency Response: 35Hz to 20kHz
• Amp output power
• (analog) 250W at 4 ohm / 150W at 8 ohm
• Sensitivity: 103 dB SPL
• Weight: 65.92 lbs.
• Dimensions: 23.39"W x 29.13"H x 18.9"D

Markbass Standard 104HF Front-Ported Neo 4x10 Bass Speaker Cabinet - Scratch 'n' Dent Features:

• Ultra-light neodymium B&C speakers
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Grill for protecting speakers
• Lightweight

This solid cab will give your bass a more "in your face" feel. Order one today.

The Markbass Standard 104HR is an exceptional, professional bass speaker cabinet that performs well in any club, big or small. The Standard 104HR cab puts out impressive power of 800W and weighs only 56 pounds. Working bassists will love the 104HR speaker cabinet for its power, high-quality sound and portability. Perfectly capable in a standalone situation, this bass speaker cab is even more ear-catching when combined with a Markbass Standard 151HR or 102HF.

Markbass Standard 104HR Rear-Ported Neo 4x10 Bass Speaker Cabinet Specifications:

• Impedance: 8 or 4 ohms
• Speaker size: 4 x 10"
• Bass Port: Rear
• Tweeter: 1" compression driver with custom horn
• Power Handling: 800W RMS (AES Standard)
• Crossover Frequency: 3.5kHz
• Frequency Response: 35Hz to 20kHz
• Sensitivity: 103 dB SPL
• Weight: 56 lbs.
• Dimensions: 23.4"W x 23.8"H x 18.9"D

Markbass Standard 104HR Rear-Ported Neo 4x10 Bass Speaker Cabinet Features:

• Ultra-light neodymium B&C speakers
• 1" compression driver with custom horn
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Grill for protecting speakers
• Lightweight

Give your bass a huge boost with this cab. Order today!

The Markbass Standard 106HR is an ultra-light and compact bass speaker cabinet with a 1" HF compression driver and custom horn and B&C designed neodymium woofers. This powerful bass cab delivers big rock sound, but the Standard 106HR is small enough to be practical club gigs.

Markbass Standard 106HR Rear-Ported Neo 6x10 Bass Speaker Cabinet Specifications:

• Impedance: 6 ohms
• Speaker size: 6 x 10"
• Bass ports: rear
• Tweeter: 1" compression driver with custom horn
• Power Handling: 1200W RMS (AES Standard)
• Crossover Frequency: 3.5kHz
• Frequency Response: 45Hz to 20kHz
• Sensitivity: 104 dB SPL
• Weight: 71.18 lbs.
• Dimensions: 23.4"W x 34.2"H x 18.9"D

Markbass Standard 106HR Rear-Ported Neo 6x10 Bass Speaker Cabinet Features:

• B&C 10" neodymium woofers
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Grill for protecting speakers
• Lightweight

Raise the woof with this exemplary bass cab. Order one today!

The Markbass Standard 151HR is a bass speaker cab that will never leave you lacking in the the bottom end department. The Standard 151HR bass cabinet's 15" speaker gives you a deep, classic sound that suits many musical styles. This cab can be used on its own, but combining it with a Markbass Traveler 102P or Standard 104HR makes for one powerful stack. So plug the Markbass Standard 151HR bass cab in and prepare to rock!

Markbass Standard 151HR Rear-Ported Neo 1x15 Bass Speaker Cabinet Specifications:

• Impedance: 8 ohm
• Speaker size: 1 x 15"
• Bass ports: rear
• Tweeter: 1" compression driver with custom horn
• Power Handling: 400W RMS (AES Standard)
• Crossover Frequency: 3.5kHz
• Frequency Response: 40Hz to 20kHz
• Sensitivity: 100 dB SPL
• Weight: 52.9 lbs.
• Dimensions: 23.4"W x 23.8"H x 18.9"D

Markbass Standard 151HR Rear-Ported Neo 1x15 Bass Speaker Cabinet Features:

• Ultra-light neodymium B&C speaker
• Rear-Ported
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Grill for protecting speakers
• Lightweight

Order this excellent cab today!

The Markbass Standard 152HR bass cab is fantastic for rock and pop. If you want to move a lot of air, you can't go wrong with two 15" speakers, especially these excellently designed B&C neodymium woofers. Combined with the 1" compression driver custom horn, and 800W of bass-driving power, we're talking plenty of sound to shake the ground.

Markbass Standard 152HR Rear-Ported Neo 2x15 Bass Speaker Cabinet Specifications:

• Impedance: 4 ohms
• Speaker size: 2 x 15"
• Bass ports: rear
• Tweeter: 1" compression driver with custom horn
• Power Handling: 800W RMS (AES Standard)
• Crossover Frequency: 3.5kHz
• Frequency Response: 35Hz to 20kHz
• Sensitivity: 103 dB SPL
• Weight: 71.7 lbs.
• Dimensions: 23.4"W x 34.2"H x 18.9"D

Markbass Standard 152HR Rear-Ported Neo 2x15 Bass Speaker Cabinet Features:

• B&C 15" neodymium woofers
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Grill for protecting speakers
• Lightweight

When an everyday bass cab won't do, pick up the lighter than expected 152HR. Order yours today.

The popular TA501 amp head helps smooth out your sound with a high-quality onboard tube compressor, featuring a JJ Electronics ECC81 tube. Tone-wise, your sound is warmed up by the tube even when the compressor is off. It also includes foot-switchable mute-to-tune, an EQ bypass, ground lift to eliminate hum, exclusive Markbass' VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters, and high-quality Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables.

Markbass TA501 500W Bass Head Specifications:

• Power
• Input impedance: 500Kohm, max. voltage: 9 Vpp
  
  Effect Return impedance: 33Kohm, max. voltage: 12 Vpp
• Output Power: 300W RMS at 8 ohm, 500W RMS at 4 ohm
• Power Requirement: 100/120V; 230V; 240V; 50/60Hz
  
  Controls
• GAIN: 80dB to +25dB range
• GROUND LIFT: Switch on rear panel
• MASTER VOLUME
• LINE OUT: level control on front panel
• PRE/POST EQ (for line out): switch on rear panel
• COMPRESSION RATIO: 1:1 (off) to infinity:1 (limiter)
• FOOTSWITCH: mute; EQ bypass
  
  Equalization
• LOW
• Center frequency: 40Hz; level ±16dB
• LOW MID
• Center frequency 100-800Hz, level ±16dB
• HIGH MID
• Center frequency 700Hz-6kHz, level ±16dB
• HIGH
• 10kHz shelf; level ±16dB
• VPF (Variable Pre-shape Filter)
• center frequency 380Hz (cut)
• VLE (Vintage Loudspeaker Emulator)
• 250Hz 20 kHz cut
  
  Outputs
• EFFECT SEND
• Unbalanced, max. voltage 12 Vpp (pre-EQ)
• TUNER OUT
• Unbalanced, max. voltage 2 Vpp
• LINE OUT
• Balanced XLR, max. voltage 25 Vpp
• SPEAKER OUT
• Speakon, 1/4"
  
  Other
• Dimensions: 14.5"(W) x 3.39"(H) x 11.89"(D)
• With rack ears: 19"W
• 2U High
• Weight: 7.5 lbs.
• COMPRESSOR TUBE
• 1 x EECC81 (JJ Electronic)

Markbass TA501 500W Bass Head Features:

• Bass amplifier with tube compressor, solid state preamp and analog power amp
• Provides 300W RMS at 8 ohm, 500W RMS at 4 ohm
• 1/4" input jack works with active or passive basses
• Gain and Master volume controls
• Clip warning light
• Tube compressor with JJ Electronics' ECC81 tube
• Comp ratio tube to control gain reduction applied to the signal which works like a limiter
• Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
• Balanced XLR out
• Line out knob controls the volume level of the Line out XLR
• EQ includes controls for Low, Mid Frequency Low, High Frequency Low, and High
• Mid Frequency High and Low level controls for deciding how much frequency area will be affected
• VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters
• Pre EQ/Post EQ switch to determine whether the output signal is effected by the EQ settings or not
• Ground lift switch to eliminate hum
• Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
• Send and Return Effect ensures main signal continues even if something dies in your effects chain
• Dual-sided fiberglass PC boards with lined perforations for high-quality solder connections
• Surface-mount components are silicon-sealed to isolate vibrations
• Computer-grade pre-assembled ribbon connector cable harnesses and ribbons for noise-free operation
• Integrated threaded posts for easy assembly/disassembly and added durability
• Rigid 2mm thick aluminium chassis for a long-lasting finish

Another quality Markbass amp head for improving your bass sound. Click or call to order one today.