The popular TA501 amp head helps smooth out your sound with a high-quality onboard tube compressor, featuring a JJ Electronics ECC81 tube. Tone-wise, your sound is warmed up by the tube even when the compressor is off. It also includes foot-switchable mute-to-tune, an EQ bypass, ground lift to eliminate hum, exclusive Markbass' VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters, and high-quality Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables.

Markbass TA501 500W Bass Head - Scratch 'n' Dent Specifications:

• Power
• Input impedance: 500Kohm, max. voltage: 9 Vpp
  
  Effect Return impedance: 33Kohm, max. voltage: 12 Vpp
• Output Power: 300W RMS at 8 ohm, 500W RMS at 4 ohm
• Power Requirement: 100/120V; 230V; 240V; 50/60Hz
  
  Controls
• GAIN: 80dB to +25dB range
• GROUND LIFT: Switch on rear panel
• MASTER VOLUME
• LINE OUT: level control on front panel
• PRE/POST EQ (for line out): switch on rear panel
• COMPRESSION RATIO: 1:1 (off) to infinity:1 (limiter)
• FOOTSWITCH: mute; EQ bypass
  
  Equalization
• LOW
• Center frequency: 40Hz; level ±16dB
• LOW MID
• Center frequency 100-800Hz, level ±16dB
• HIGH MID
• Center frequency 700Hz-6kHz, level ±16dB
• HIGH
• 10kHz shelf; level ±16dB
• VPF (Variable Pre-shape Filter)
• center frequency 380Hz (cut)
• VLE (Vintage Loudspeaker Emulator)
• 250Hz 20 kHz cut
  
  Outputs
• EFFECT SEND
• Unbalanced, max. voltage 12 Vpp (pre-EQ)
• TUNER OUT
• Unbalanced, max. voltage 2 Vpp
• LINE OUT
• Balanced XLR, max. voltage 25 Vpp
• SPEAKER OUT
• Speakon, 1/4"
  
  Other
• Dimensions: 14.5"(W) x 3.39"(H) x 11.89"(D)
• With rack ears: 19"W
• 2U High
• Weight: 7.5 lbs.
• COMPRESSOR TUBE
• 1 x EECC81 (JJ Electronic)

Markbass TA501 500W Bass Head - Scratch 'n' Dent Features:

• Bass amplifier with tube compressor, solid state preamp and analog power amp
• Provides 300W RMS at 8 ohm, 500W RMS at 4 ohm
• 1/4" input jack works with active or passive basses
• Gain and Master volume controls
• Clip warning light
• Tube compressor with JJ Electronics' ECC81 tube
• Comp ratio tube to control gain reduction applied to the signal which works like a limiter
• Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
• Balanced XLR out
• Line out knob controls the volume level of the Line out XLR
• EQ includes controls for Low, Mid Frequency Low, High Frequency Low, and High
• Mid Frequency High and Low level controls for deciding how much frequency area will be affected
• VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters
• Pre EQ/Post EQ switch to determine whether the output signal is effected by the EQ settings or not
• Ground lift switch to eliminate hum
• Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
• Send and Return Effect ensures main signal continues even if something dies in your effects chain
• Dual-sided fiberglass PC boards with lined perforations for high-quality solder connections
• Surface-mount components are silicon-sealed to isolate vibrations
• Computer-grade pre-assembled ribbon connector cable harnesses and ribbons for noise-free operation
• Integrated threaded posts for easy assembly/disassembly and added durability
• Rigid 2mm thick aluminium chassis for a long-lasting finish

Another quality Markbass amp head for improving your bass sound. Click or call to order one today.

The Markbass TA503 has a premium tube preamp that gives this bass amp head the advantage of tube warmth and analog clarity simultaneously. The TA503 bass head boasts a flexible EQ with 4-band semi-parametric tone control and Markbass' signature VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters. Markbass gave the TA503 bass amplifier a Pre EQ/Post EQ switch to determine whether the output signal is affected by the EQ settings or not, as well as Send and Return Effect I/O to insure your main signal continues even if something along your effect chain breaks or runs out of batteries. An optional footswitch provides mute-to-tune and EQ bypass control.

Markbass TA503 500W Bass Amp Head Specifications:

• Power
• Passive Input impedance: 500Kohm, max. voltage: 4 Vpp
• Effect return impedance: 500Kohm, max. voltage: 10 Vpp
• Active Input impedance: 500Kohm, max. voltage: 10 Vpp
• Output Power: 300W RMS at 8 ohms, 500W RMS at 4 ohms
• Power Requirement: 100/120V; 230V; 240V; 50/60Hz
  
  Controls
• GAIN: 80dB to +35dB range
• LINE OUT: Level control on front panel
• PRE/POST EQ (for line out): Switch on rear panel
• GROUND LIFT: Switch on rear panel
• MASTER VOLUME
• FOOTSWITCH: Mute, EQ bypass
  
  Equalization
• LOW
• Center frequency: 40-300Hz; level ±16dB
• LOW-MID
• Semi-parametric: frequency 100 800Hz, level ±16dB
• HIGH-MID
• Semi-parametric: frequency 700Hz 6kHz, level ±16dB
• HIGH
• Semi-parametric: 1.5-10kHz shelf; level ±16dB
• VPF (Variable Pre-shape Filter)
• Center frequency: 380Hz (cut)
• VLE (Vintage Loudspeaker Emulator)
• 250Hz 20kHz cut
  
  Outputs
• EFFECT SEND
• Unbalanced, max. voltage 20 Vpp (pre-EQ)
• TUNER OUT
• Unbalanced, max. voltage 2 Vpp
• LINE OUT
• Balanced XLR, max. voltage 15 Vpp
• SPEAKER OUT
• Speakon, 1/4"
  
  Other
• Dimensions: 14.5"(W) x 3.39"(H) x 11.89"(D)
• 2U tall
• 19"(W) with rack ears
• Weight: 8.6lbs.
• Tubes: 1 x EECC81, 1 x ECC83 (JJ Electronic)

Markbass TA503 500W Bass Amp Head Features:

• Tube preamp analog bass head
• Provides 300W RMS at 8 ohms, 500W RMS at 4 ohms
• 1/4" input jack works with active or passive basses
• Gain and Master volume controls
• Clip warning light
• Line out volume control knob
• EQ includes controls for Low, Mid Frequency Low, High Frequency Low, and High
• Mid Frequency High and Low level controls for deciding how much frequency area will be affected
• VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters
• Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
• Balanced XLR out
• Pre EQ/Post EQ switch to determine whether the output signal is effected by the EQ settings or not
• Ground lift switch to eliminate hum
• Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
• Send and Return Effect ensures main signal continues even if something dies in your effects chain
• Dual-sided fiberglass PC boards with lined perforations for high-quality solder connections
• Surface-mount components are silicon-sealed to isolate vibrations
• Computer-grade pre-assembled ribbon connector cable harnesses and ribbons for noise-free operation
• Integrated threaded posts for easy assembly/disassembly and added durability
• Rigid 2mm thick aluminium chassis for a long-lasting finish

Enhance your sound with this top-notch preamp head. Order one today!

The Markbass TA503 has a premium tube preamp that gives this bass amp head the advantage of tube warmth and analog clarity simultaneously. The TA503 bass head boasts a flexible EQ with 4-band semi-parametric tone control and Markbass' signature VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters. Markbass gave the TA503 bass amplifier a Pre EQ/Post EQ switch to determine whether the output signal is affected by the EQ settings or not, as well as Send and Return Effect I/O to insure your main signal continues even if something along your effect chain breaks or runs out of batteries. An optional footswitch provides mute-to-tune and EQ bypass control.

Markbass TA503 500W Bass Amp Head - Scratch 'n' Dent Specifications:

• Power
• Passive Input impedance: 500Kohm, max. voltage: 4 Vpp
• Effect return impedance: 500Kohm, max. voltage: 10 Vpp
• Active Input impedance: 500Kohm, max. voltage: 10 Vpp
• Output Power: 300W RMS at 8 ohms, 500W RMS at 4 ohms
• Power Requirement: 100/120V; 230V; 240V; 50/60Hz
  
  Controls
• GAIN: 80dB to +35dB range
• LINE OUT: Level control on front panel
• PRE/POST EQ (for line out): Switch on rear panel
• GROUND LIFT: Switch on rear panel
• MASTER VOLUME
• FOOTSWITCH: Mute, EQ bypass
  
  Equalization
• LOW
• Center frequency: 40-300Hz; level ±16dB
• LOW-MID
• Semi-parametric: frequency 100 800Hz, level ±16dB
• HIGH-MID
• Semi-parametric: frequency 700Hz 6kHz, level ±16dB
• HIGH
• Semi-parametric: 1.5-10kHz shelf; level ±16dB
• VPF (Variable Pre-shape Filter)
• Center frequency: 380Hz (cut)
• VLE (Vintage Loudspeaker Emulator)
• 250Hz 20kHz cut
  
  Outputs
• EFFECT SEND
• Unbalanced, max. voltage 20 Vpp (pre-EQ)
• TUNER OUT
• Unbalanced, max. voltage 2 Vpp
• LINE OUT
• Balanced XLR, max. voltage 15 Vpp
• SPEAKER OUT
• Speakon, 1/4"
  
  Other
• Dimensions: 14.5"(W) x 3.39"(H) x 11.89"(D)
• 2U tall
• 19"(W) with rack ears
• Weight: 8.6lbs.
• Tubes: 1 x EECC81, 1 x ECC83 (JJ Electronic)

Markbass TA503 500W Bass Amp Head - Scratch 'n' Dent Features:

• Tube preamp analog bass head
• Provides 300W RMS at 8 ohms, 500W RMS at 4 ohms
• 1/4" input jack works with active or passive basses
• Gain and Master volume controls
• Clip warning light
• Line out volume control knob
• EQ includes controls for Low, Mid Frequency Low, High Frequency Low, and High
• Mid Frequency High and Low level controls for deciding how much frequency area will be affected
• VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters
• Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
• Balanced XLR out
• Pre EQ/Post EQ switch to determine whether the output signal is effected by the EQ settings or not
• Ground lift switch to eliminate hum
• Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
• Send and Return Effect ensures main signal continues even if something dies in your effects chain
• Dual-sided fiberglass PC boards with lined perforations for high-quality solder connections
• Surface-mount components are silicon-sealed to isolate vibrations
• Computer-grade pre-assembled ribbon connector cable harnesses and ribbons for noise-free operation
• Integrated threaded posts for easy assembly/disassembly and added durability
• Rigid 2mm thick aluminium chassis for a long-lasting finish

Enhance your sound with this top-notch preamp head. Order one today!

The Markbass Traveler 102P is one of the smallest and lightest 2 x 10" bass speaker cabinets on the market. Use the 102P cab in either a vertical or horizontal position. Perfect for club gigs, the Traveler 102P bass cabinet shines even more when added to a Traveler 151P for a punchy, full-range sound. Features B&C lightweight woofers and a Piezo tweeter.

Markbass Traveler 102P Rear-Ported Compact 2x10 Bass Speaker Cabinet Specifications:

• Impedance: 8 or 4 ohms
• Speaker size: 2 x 10"
• Bass Port: Rear
• Tweeter: Piezo
• Power Handling: 400W RMS (AES Standard)
• Crossover Frequency: 3.5kHz
• Frequency Response: 45Hz to 18kHz
• Sensitivity: 101 dB SPL
• Weight: 33 lbs.
• Dimensions: 23.4"W x 13"H x 17"D

Markbass Traveler 102P Rear-Ported Compact 2x10 Bass Speaker Cabinet Features:

• Ultra-light neodymium B&C speakers
• Piezo tweeter
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Grill for protecting speakers
• Lightweight

Boost your bass with this well crafted combo designed with the gigging musician in mind. Order today.

The Markbass Traveler 121H is a fantastic speaker cab for bass players who need a small, yet warm-sounding rig. The fact that the Traveler 121H won the 2007 Best Bass Cabinet MIPA award should make it an even easier choice, especially for acoustic bass players. Made of sturdy, yet lightweight construction, the rear-ported Markbass Traveler 121H features a 12" neodymium woofer from B&C and a 1" compression driver with custom horn.

Markbass Traveler 121H Rear-Ported Compact 1x12 Bass Speaker Cabinet Specifications:

• Impedance: 8 ohms
• Speaker size: 1 x 12"
• Bass ports: rear
• Tweeter: 1" compression driver with custom horn
• Power Handling: 400W RMS (AES Standard)
• Crossover Frequency: 3.5kHz
• Frequency Response: 40Hz to 20kHz
• Sensitivity: 99 dB SPL
• Weight: 34.61 lbs.
• Dimensions: 23.39"W x 15.35"H x 17.05"D

Markbass Traveler 121H Rear-Ported Compact 1x12 Bass Speaker Cabinet Features:

• B&C 12" woofer
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Grill for protecting speakers
• Lightweight
• Redesigned to stack with Standard Series cabs
• On it's side it also stacks with the Mini CMD 121P and CMD 121H combos

Get a more intimate sound out of your bass with this compact cab. Order today!

The Markbass Traveler 151P is one of the smallest, lightest 15" bass speaker cabs on the market. Putting power and pro sound into a very practical package, the Marbass Traveler 151P is an ideal bass cab for club gigs, especially in pairs. 151P bass speakers can also be stacked with any of Markbass' Standard Series cabinets for even more quality sound. The Markbass Traveler 151P speaker cabinet's high-grade, multi-ply poplar shell design and the B&C woofer add up to a sturdy combination that is shockingly lighter than its peers.

Markbass Traveler 151P Rear-Ported Compact 1x15 Bass Speaker Cabinet Specifications:

• Impedance: 8 ohms
• Speaker size: 1 x 15"
• Power Handling: 400W RMS (AES Standard)
• Bass port: Rear
• Crossover Frequency: 3.5kHz
• Frequency Response: 40Hz to 18kHz
• Sensitivity: 100 dB SPL
• Weight: 37.3 lbs.
• Dimensions: 23.39"W x 18.3"H x 17.05"D

Markbass Traveler 151P Rear-Ported Compact 1x15 Bass Speaker Cabinet Features:

• Ultra-light neodymium B&C speaker
• Redesigned to stack on all Standard Series cabinets
• Great power-to-weight ratio
• Made of high-grade, multi-ply poplar
• Glued, screwed, and sealed internally with special compounds for maximum sound quality
• Protected corners
• Grill for protecting speaker
• Lightweight

Add this little powerhouse to your kit. Order today!

The tiny Markbass Tweeter Box External Tweeter can be easily transported from practice space to practice space. If you own a Micromark practice amp and feel you're missing out some of the higher frequencies, this little external Tweeter Box will solve your problem. Weighs less than half a pound. Just plug the Markbass Tweeter Box into your Micromark, use the velcro-padded bottom to help secure it and start rediscovering your high-end response. The tweeter itself is a Piezo that produces 20W RMS (AES Standard) power of sound.

NOTE: To maximize the volume produced by your Micromark, place the combo on the floor for the fullest low end, and angle the tweeter toward ear-level so you can hear the more directional high frequencies.

Markbass Tweeter Box External Tweeter for Micromark Specifications:

• Impedance: none
• Tweeter: Piezo
• Power: 20W RMS (AES standard)
• Frequency Response: 5kHz to 18kHz
• Sensitivity: 108 dB SPL
• Weight: 0.28 lbs.
• Dimensions: 2.8"W x 2.8"H x 3.5"D

Markbass Tweeter Box External Tweeter for Micromark Features:

• For use with a Micromark practice amp
• Velcro pad on bottom for secure placement

Add a lightweight external tweeter to your Micromark for a more complete tonal experience while you work on your music. Order it today.

The Marshall MB15 is a 15 Watt combo bass amp with features that belie its size. 2 channels offer both classic and modern voicing. The Modern channel has a handy compression feature to allow you to practice with awesome, high-volume sound at a level that won't have your neighbors calling the police. The Classic channel sports the tried-and-true volume and gain knobs you know and love. A 3-band EQ allows further tone shaping, a CD-in jack allows you to easily jam with recordings, and a 1/4" line-out jack plugs you right into the PA, a recorder, or external speaker.

Marshall MB15 Bass Combo Amp Specifications:

• 15 Watt
• 1x8" speaker
• 2 channels
• 381mm x 368mm x 241mm
• Ported cabinet
• Metal reinforced corners
• Top handle
• 1/4" input jack
• Power switch

Marshall MB15 Bass Combo Amp Features:

• Modern/Classic switch
• Modern channel: volume knob, compressor knob with switch and LED
• Classic channel: gain knob, volume knob
• Equalizer: bass, voice, treble
• 1/4" jacks: Input, CD in, line out, headphones

Put it in the cart.

The Marshall MB150 is a hybrid combo bass guitar amplifier that offers 150W through a 15" speaker. This superb Marshall bass combo offers the tone and versatility required by any professional bass player.

The Marshall MB150 bass combo offers the tone and versatility required by any professional bass player. The MB150 bass amp has 2 channels (Modern and Classic) with separate EQ for each. The Modern channel features bass, treble, parametric mid, and a switchable compressor with variable level control. The Classic channel with its ECC83 pre-amp valve includes a Boost switch and has a 3-band passive tone network featuring a mid Voice control with three modes. The channels are selectable via the suppled single footswitch.

Marshall MB150 150W 1x15" Hybrid Bass Combo Amp Specifications:

• Dimensions: 580 x 585 x 355 mm
• Weight: 30 Kg.

Marshall MB150 150W 1x15" Hybrid Bass Combo Amp Features:

• Superb Marshall bass combo offers the tone and versatility required by any professional bass player
• 150 watts Output
• 1x15 inch speaker
• Built-in limiter
• DI Line out: XLR (Pre and Post)
• FX Loop
• Headphone output
• Footswitch: 1 Way (included)
• 2 channels, Modern and Classic
• Built-in compressor (switchable Modern channel)
• ECC83 pre-amp valve (Classic channel)
• Boost Switch (Classic channel)
• CD input (1/4 inch jack)

Marshall MB150 150W 1x15" Hybrid Bass Combo Amp Includes:

• 2-button footswitch

Really feel that bass, order yours today!

The Marshall MB30 is a 30W bass combo amp with features that will have you grinning from ear to ear. 2 channels offer both classic and modern voicing. The MB30 amp's Modern channel has a handy compression feature to allow you to practice with awesome, high-volume sound at a level that won't have your neighbors calling the police. The Classic channel sports the tried-and-true volume and gain knobs you know and love. The Marshall MB30 amplifier's 3-band EQ allows further tone shaping, and a CD-in jack allows you to easily jam with recordings.

Marshall MB30 Bass Combo Amp Specifications:

• 30 Watt
• 1x10" speaker
• 2 channels
• 438mm x 400mm x 260mm
• Ported cabinet
• Metal reinforced corners
• Top handle
• 1/4" input jack
• Power switch

Marshall MB30 Bass Combo Amp Features:

• Modern/Classic switch
• Modern channel: volume knob, comp knob with switch and LED
• Classic channel: gain knob, volume knob
• Equalizer: bass, 3-position voice shift, voice, treble
• 1/4" jacks: Input, CD in, headphones

Put it in the cart and get ready to groove.

The Marshall MB4210 higher wattage bass combo amp is just what the doctor ordered. The Marshall MB4210 is for those wanting to leave a lasting impression with not only the audience, but also with fellow band members. The MB4210 bass amp will send fat and heavy signals thudding through the chest of everybody within 200 yards! This 450W, 2x10 combo with HF horn has 2 channels (Modern and Classic) with separate EQ for each. The Modern channel features bass, treble, a parametric mid, and a switchable compressor with variable level control. The Classic channel with its ECC83 preamp valve includes a Boost switch, and has a 3-band passive tone network. The MB4210 bass amp also lets you select a blend of the two channels either from the front panel, or via a supplied two-way footswitch. The overall volume of the blend is adjustable in addition to the balance between the 2 channels.

Marshall MB4210 300W/450W 2x10" Hybrid Bass Combo Amp Specifications:

• Dimensions: 630 x 535 x 280 mm
• Weight: 33 Kg

Marshall MB4210 300W/450W 2x10" Hybrid Bass Combo Amp Features:

• Sends booming bottom-end signals thudding through the chest of everybody within a 200 yard radius!
• 300 watts Output @ 4 Ohms
• 450 watts Output @ 2 Ohms (with extension cabinet)
• 2 x 10 inch speakers
• HF Horn
• Speakon connectors x 2
• 1/4" jack speaker connectors x 2
• Built-in limiter
• DI Line out: XLR (Pre and Post)
• FX Loop
• Footswitch: 2 Way (included)
• 2 channels, Modern and Classic
• Blend control
• Built-in compressor (switchable Modern channel)
• ECC83 pre-amp valve (Classic channel)
• Boost Switch (Classic channel)
• Mid Voices
• Master Volume
• CD input (1/4 inch jack)
• Headphone output

Leave a lasting impression on everyone who hears you, call or click now!

The Marshall MB4410 is the daddy of bass combo amps. The 450 Watt bass combo houses 4x10" speakers, and an HF horn. It's big enough to sound monstrous, yet transportable enough to fit in the car. The Marshall bass combo booms with low frequency bottom-end. The MB4410 amp features 2 channels-Modern and Classic-with a separate EQ for each. Modern features include bass, treble, parametric mid and switchable compressor with variable level control. The Classic channel with its ECC83 pre-amp valve includes a Boost switch and has a 3-band passive tone network. You can mix the Marshall MB4410 amp's 2 channels either from the front panel or from the supplied 2-way footswitch. The overall volume of the blend is adjustable in addition to the balance between the 2 channels.

Marshall MB4410 Hybrid Bass Combo Specifications:

• Dimensions: 630 x 720 x 410 mm
• Weight: 51 Kg

Marshall MB4410 Hybrid Bass Combo Features:

• Big enough to sound monstrous, yet transportable enough to fit in the car!
• 300 watts Output @ 4 Ohms
• 450 watts Output @ 2 Ohms (with extension cabinet)
• 4 x 10 inch speakers
• HF Horn
• Speakon connectors x 2
• 1/4 inch jack speaker connectors x 2
• Built-in limiter
• DI Line out: XLR (Pre and Post)
• FX Loop
• Footswitch: 2 Way (included)
• 2 channels, Modern and Classic
• Blend control
• Built-in compressor (switchable Modern channel)
• ECC83 pre-amp valve (Classic channel)
• Boost Switch (Classic channel)
• 3 x Mid Voices
• Master Volume
• CD input (1/4 inch jack)
• Headphone output

Order today and rumble wherever you play!

The Marshall MB450H is a powerhouse amp head for your bass. It wallops a massive 450W of total bass power when connected to 2 extension cabinets. All that's left to do now is to choose your preferred choice of cabinets so you can plug in and rock!

Both channels-Modern and Classic-have separate EQ. The Modern channel features bass, treble, parametric mid and a compressor. The Classic channel with its ECC83 preamp valve includes a Boost switch, and it has a 3-band passive tone network with 3 different voices. Like the high-wattage Marshall combo amps, the MB450 bass head has the option of blending the 2 channels either from the front panel or via a supplied 2-way footswitch.

Marshall MB450H 450W Hybrid Bass Amp Head Specifications:

• Dimensions: 630 x 220 x 235 mm
• Weight: 15 Kg

Marshall MB450H 450W Hybrid Bass Amp Head Features:

• Superb, versatile two channel Bass Amp head with a monstrous 450 watt power output
• 300 watts Output @ 4 Ohms
• 450 watts Output @ 2 Ohms
• Speakon connectors x 2
• 1/4 inch jack speaker connectors x 2
• Built-in limiter
• DI Line out: XLR (Pre and Post)
• FX Loop
• Footswitch: 2 Way (included)
• 2 channels, Modern and Classic
• Blend control
• Built-in compressor (switchable Modern channel)
• ECC83 pre-amp valve (Classic channel)
• Boost Switch (Classic channel)
• 3 x Mid Voices
• Master Volume
• CD input (1/4 inch jack)
• Headphone output

Marshall MB450H 450W Hybrid Bass Amp Head Includes:

• 2-button footswitch

Powerful punch, along with quality. Click or call now!

The portable Marshall MB60 is a 60W, 1x12 bass combo amp that packs a mighty bottom-end punch making it ideal for rehearsal rooms or pub gigs. The MB60 combo has 2 channels-Modern and Classic-with separate EQ for each. The Modern channel features Bass, Treble, parametric Mid, and switchable compressor with variable level control. The Classic channel, with its ECC83 pre-amp valve, includes a Boost switch, 3-band passive tone network, and features a mid-Voice control with 3 modes. Both channels are selectable via the supplied single footswitch.

Marshall MB60 60W 1x12" Hybrid Bass Combo Amp Specifications:

• Power (RMS): 60W
• Speaker configuration: 1 x 12"
  
  Dimensions (mm): 535 x 505 x 325mm
• Weight: 23kg

Marshall MB60 60W 1x12" Hybrid Bass Combo Amp Features:

• Compressor
• EXX83 Pre-Amp Valve
• Boost Switch
• Mid Voices
• FX Loop
• 2 Channels
• Limiter
• DI Line Out: XLR (Pre & Post)
• Footswitch (1-way) included

Marshall MB60 60W 1x12" Hybrid Bass Combo Amp Includes:

• footswitch

Get the mighty bottom-end punch ideal for the rehearsal room or the pub gig today!

The Marshall MBC115 is a 300W, 4-ohm bass speaker cabinet, sturdily built and ready for life on the road. The MBC115 speaker cab contains one 15" speaker with an HF horn. Marshall listened to bass players' requirements, and made the decision to give you options of the most favored and asked-after extension cabinets, to complement your bass head or combo. This extension cabinet can be used with the Marshall MB450H amp head, as well as the range of Marshall MB bass combos, and it is finished in Marshall black textured vinyl with a black speaker grill.

Marshall MBC115 1x15" Bass Reflex Speaker Cabinet Specifications:

• Dimensions: 630 x 635 x 410 mm
• Weight: 32 Kg

Marshall MBC115 1x15" Bass Reflex Speaker Cabinet Features:

• Superb bass cabinet, ideal for use with the Marshall bass amp head and combos
• Cabinet Type: Bass reflex
• Speaker Configuration: 1 x 15 inch
• HF Horn
• HF Horn switch
• Impedance: 4 ohms
• Power (RMS): 300 Watt
• Power (Program): 600 Watt
• Speakon connector x 1
• 1/4" jack speaker connector x 1

Get the punch your looking for with this great cabinet today!

The Marshall MBC410 Bass Guitar Extension Cabinet, has a 600W RMS rating, and 4X10" speakers. It's a superb, colossal-sounding bass cabinet, ideal for use with Marshall bass amp heads and combos.

The Marshall MBC410 is loaded with four 10" speakers that deliver clear, low-end tones throughout the club. It also has an HF horn and is sturdily built, ready for life on the road. Marshall listened to bass players' requirements, and made the decision to give you options of the most favored and asked-after extension cabinets to complement your bass head or combo.

This extension cabinet can be used with the Marshall MB450H amp head as well as the range of Marshall MB bass combos and is finished in Marshall black textured vinyl with a black speaker grill.

Marshall MBC410 4x10" Bass Reflex Speaker Cabinet Specifications:

• Dimensions: 630 x 720 x 410 mm
• Weight: 42.5 Kg

Marshall MBC410 4x10" Bass Reflex Speaker Cabinet Features:

• Superb, colossal-sounding bass cabinet, ideal for use with the Marshall bass amp head and combo
• Cabinet Type: Bass reflex
• Speaker Configuration: 4x10"
• HF Horn
• HF Horn switch
• Impedance: 4 Ohms
• Power (RMS): 600 Watt
• Power (Program): 1200 Watt
• Speakon connector x 1
• 1/4" jack speaker connector x 1

Why wait to deliver clear low-end tones through the clubs, click or call today!

The Marshall MBC810 Bass Guitar Extension Cabinet, has a 1200 Watt rating, and 8x10" speakers. It is a superb, mighty 1200 Watt bass cabinet, ideal for use with the Marshall bass amp head and combos.

The Marshall MBC810, is the bigger brother of the 4x10", and it not only sounds the part, it also looks the part. This mighty 1200 Watt, 4 Ohm beast contains 8x10" speakers with an HF horn. Marshall listened to bass players' requirements, and made the decision to give you options of the most favored, and asked-after extension cabinets to complement your bass head, or combo. The MBC810 extension cabinet can be used with the Marshall MB450H amp head, as well as the range of Marshall MB bass combos, and is finished in Marshall black textured vinyl with a black speaker grille.

Marshall MBC810 8x10" Bass Reflex Speaker Cabinet Specifications:

• Dimensions: 630 x 1250 x 410 mm
• Weight: 70 Kg

Marshall MBC810 8x10" Bass Reflex Speaker Cabinet Features:

• Superb, mighty 1200 Watt bass cabinet, ideal for use with the Marshall bass amp head and combos
• Cabinet Type: Bass reflex
• Speaker Configuration: 8x10"
• HF Horn
• HF Horn switch
• Impedance: 4 Ohms
• Power (RMS): 1200 Watt
• Power (Program): 2400 Watt
• Speakon connector x 1
• 1/4" jack speaker connector x 1

Why wait to get yourself heard with clear low-end tones, just click or call today!

These Nady ProPower PSW152 Subwoofers were developed using the expertise of professional sound engineers and working musicians. They are ruggedly built, have exceptional sound, superior performance, and great flexibility at a very affordable price.

Nady PSW-152 Subwoofer Pair Specifications:

• 20-400Hz frequency response
• Max SPL 107db at 1M
• Dual mounting pole adapters
• 39.5" x 22" x 20.2"
• 107 lbs. each

Nady PSW-152 Subwoofer Pair Features:

• Dual 15" subwoofer speakers
• 800W peak power rating-400W RMS
• 4-ohm cabinets
• Durable black carpet covering
• Heavy duty plastic protective corners
• Integrated recessed carrying handles for
• easy handling
• Binding posts (banana jacks) and two 1/4" (6.3mm) jack inputs

Order today and put some thump in your sound.

The Nemesis N10 Bass Combo is a perfect small-size kickback bass amplifier for practice or warm-up. At 50 watts, the N10 is among the most powerful amps in its class. The Nemesis N10 features a wide-range 10" Eden designed coaxial loudspeaker for great tone. Nemesis houses the N10 in a strong, lightweight plywood enclosure. The bass combo contains a fully automatic AGC compression circuit on the input stage to give every note a well-balanced sound. It is coupled to a smooth-sounding, old-school passive 3-band tone control circuit. You can set the N10 bass amp up to sound sweet and clean or crank on plenty of crunch. An aux input and head phones output complete the N10 amplifier package.

Nemesis N10 Bass Combo Amp Specifications:

• Power: 50W RMS at 4 ohms
• Speakers: 10"
• Tweeter: Mechanical
• Power Handling: 50W RMS
• Frequency Respo2nse: 42hz - 13khz ±2dB
• Impedence: 4ohms
• Dimensions: 14.5"W x 17.5"H x 13"D
• Weight: 27lbs.

Nemesis N10 Bass Combo Amp Features:

• Compact
• 10" speaker
• Lightweight plywood enclosure
• Kickback design
• Heavy-duty steel grill
• Solid, balanced tone
• AGC-controlled input stage
• Gain, Master Volume controls
• 3-band EQ
• Aux input
• Headphone jack

Mobile and able to produce surprisingly powerful sound, this practice bass combo is priced to move. Order today!

The Nemesis N12 is a powerful kick-back combo amplifier that is ideal for small gigs and rehearsals. The Nemesis N12 features a 150W power rating putting it at the top of its class. The N12 combo has a seamless wide range input with an AGC-controlled input stage featuring built-in auto compression, a total sound shaping Enhance control, coupled with a powerful three-band active tone control. The N12 bass amplifier comes equipped with an aux input and a headphone out that automatically mutes the speaker output when you use the headphone jack. The Nemesis N12 bass combo also has an optimally tuned plywood bass reflex enclosure and a strong, broad range, and Eden-designed coaxial 12" speaker for great punch and tone.

Nemesis N12 Bass Combo Amp Specifications:

• Power: 150W RMS at 4ohms
• Speakers: 12"
• Tweeter: Mechanical
• Power Handling: 150W RMS
• Frequency Response: 42hz - 12khz ±2dB
• Impedence: 4ohms
• Dimensions: 18.5"W x 20.5"H x 13"D
• Weight: 43lbs.

Nemesis N12 Bass Combo Amp Features:

• Compact
• 12" speaker
• Optimally tuned bass reflex plywood enclosure
• Kickback design
• Heavy-duty steel grill
• Lightweight
• Solid, balanced tone
• AGC-controlled input stage
• Gain, Enhance controls
• 3-band EQ
• Headphone jack mutes speaker when used

Save big on this small 12" bass combo that will give you plenty bang for your buck. Order now.