The MAG C115-300 has massive power and classic Ashdown tone.

The MAG C115-300 Combo features a potent, fan-cooled 307W RMS power section and a 15" Ashdown BlueLine speaker. Rotary bass, mid, and treble controls are supplemented by smaller rotary controls providing 15dB of cut and boost at 220Hz and 1.6kHz, making it a comprehensive 5-band EQ section. Additionally, front panel push switches for Bright and Deep settings provide instant access to either attacking or warm, rounded sounds. For enhanced low-end response, the MAG C115-300 has Ashdown's acclaimed sub-harmonic generator ready to take your tone on a deep dive. Inputs are provided for active and passive instruments and the front panel also features an effects send and return, a tuner/line output and a balanced DI output for direct connection to a mixing console.

Ashdown BlueLine speakers achieve a superb balance of power, transparency and deep, controlled low end, without sacrificing any of the mid-band attack and high-end brightness that are so important in a modern bass sound.

Ashdown MAG C115-300 Combo Bass Amp Specifications:

• Output: 307W RMS
• Signal to Noise: Better than 80dB (EQ flat)
• Frequency Response: 17Hz - 300kHz
• Distortion: Less than 0.5% THD
• Dimensions: 30-1/4"W x 25-4/5"H x 18-3/4"D
• Weight: 66 lbs.

Ashdown MAG C115-300 Combo Bass Amp Features:

• 307W RMS power
• 15" BlueLine speaker
• Bass, middle and treble controls
• Rotary controls for 15dB of cut/boost at 220Hz and at 1.6kHz
• Front panel shape switches for Bright and Deep settings
• Ashdown's acclaimed sub-harmonic generator for enhanced low-end response
• Active and passive bass inputs
• Effects send and return
• Tuner/line output
• Balanced DI output
• Extension cab outputs
• Black carpet exterior
• Steel grille

A power-packed combo with bright, bold Ashdown sound. Call or click to buy now!

The MAG C115-300 has massive power and classic Ashdown tone.

The C210T-300 Combo features a potent, fan-cooled 307W RMS power section, 2 - 10" Ashdown BlueLine speakers, and a tweeter for the high frequencies. Rotary bass, mid, and treble controls are supplemented by smaller rotary controls, providing 15dB of cut and boost at 220Hz and 1.6kHz, making it a comprehensive 5-band EQ section. Additionally, front panel push switches for Bright and Deep settings provide instant access to either attacking or warm, rounded sounds. For enhanced low-end response, the C210T-300 has Ashdown's acclaimed subharmonic generator ready to take your tone on a deep dive. Inputs are provided for active and passive instruments, and the front panel also features an effects send and return, a tuner/line output, and a balanced DI output for direct connection to a mixing console.

Ashdown BlueLine speakers achieve a superb balance of power, transparency, and deep, controlled low end without sacrificing any of the mid-band attack and high-end brightness that are so important in modern bass sound.

Ashdown MAG C210T-300 Combo Bass Amp Specifications:

• Output: 307W RMS
• Signal to Noise: Better than 80dB (EQ flat)
• Frequency Response: 17Hz - 300kHz
• Distortion: Less than 0.5% THD
• Dimensions: 25-4/5"W x 30-1/4"H x 20-1/2"D
• Weight: 77 lbs.

Ashdown MAG C210T-300 Combo Bass Amp Features:

• 307W RMS power
• 2 - 10" BlueLine speakers and tweeter
• Bass, middle, and treble controls
• Rotary controls for 15dB of cut/boost at 220Hz and at 1.6kHz
• Front panel shape switches for Bright and Deep settings
• Ashdown's acclaimed subharmonic generator for enhanced low-end response
• Active and passive bass inputs
• Effects send and return
• Tuner/line output
• Balanced DI output
• Extension cab outputs
• Black carpet exterior
• Steel grille

A power-packed combo with bright, bold Ashdown sound. Call or click to buy now!

The MAG C115-300 has massive power and classic Ashdown tone.

The C410T-300 combo features a potent, fan-cooled 307W RMS power section, 4 - 10" Ashdown BlueLine speakers and a tweeter for the high frequencies. Rotary bass, mid, and treble controls are supplemented by smaller rotary controls, providing 15dB of cut and boost at 220Hz and 1.6kHz, making it a comprehensive 5-band EQ section. Additionally, front panel push switches for Bright and Deep settings provide instant access to either attacking or warm, rounded sounds. For enhanced low-end response, the C410T-300 has Ashdown's acclaimed subharmonic generator ready to take your tone on a deep dive. Inputs are provided for active and passive instruments and the front panel also features an effects send and return, a tuner/line output, and a balanced DI output for direct connection to a mixing console.

Ashdown BlueLine speakers achieve a superb balance of power, transparency, and deep, controlled low end without sacrificing any of the mid-band attack and high-end brightness that are so important in modern bass sound.

Ashdown MAG C410T-300 Combo Bass Amp Specifications:

• Output: 307W RMS
• Signal to Noise: Better than 80dB (EQ flat)
• Frequency Response: 17Hz - 300kHz
• Distortion: Less than 0.5% THD
• Dimensions: 24"W x 31"H x 13-1/5"D
• Weight: 98 lbs.

Ashdown MAG C410T-300 Combo Bass Amp Features:

• 307W RMS power
• 4 - 10" BlueLine speakers and tweeter
• Bass, middle, and treble controls
• Rotary controls for 15dB of cut/boost at 220Hz and at 1.6kHz
• Front panel shape switches for Bright and Deep settings
• Ashdown's acclaimed subharmonic generator for enhanced low-end response
• Active and passive bass inputs
• Effects send and return
• Tuner/line output
• Balanced DI output
• Extension cab outputs
• Black carpet exterior
• Steel grille

A power-packed combo with bright, bold Ashdown sound. Call or click to buy now!

The Perfect Ten is a solid little amp that's great for the bedroom or small gigs.

The Perfect Ten bass amp combines a 30W power section with a single 10" Ashdown BlueLine bass speaker. Sounds can be shaped quickly and intuitively using bass, mid, and treble controls, supplemented by a pre-shaped deep switch for added enhancement. Headphone output lets you practice whenever you want, and the external speaker out lets you connect another cab with ease.

Ashdown Perfect Ten 10" Combo Bass Amp Specifications:

• Output Power: 30W RMS
• Input Impedance: 1M Ohm
• Input Signal Range: 100mV to 10V
• 17-1/2"W x 19-9/10"H x 19-7/10"D
• 47 lbs.

Ashdown Perfect Ten 10" Combo Bass Amp Features:

• 30W
• 10" Ashdown BlueLine speaker
• 3-band EQ
• Deep switch
• Headphone out
• External cab out

Quality Ashdown tone in a compact combo. Call or click to buy now!

A consumate cab in every way.

The versatile D10BX-D speaker cab is ideal for electric bass guitar, acoustic bass, electric guitar, and the Chapman Stick.

The Deep Red series combines Bag End's long standing acoustical designs for bass instruments with modern state of the art materials and production techniques. The subtle deep red color blends toward black at a distance but up close it radiates a subtle deep ruby red color. Under the carpet the speaker enclosure is made from the finest void free hardwood plywood and incorporates precision-machined joints and modern adhesives for unsurpassed road worthiness.

The Deep Red X series incorporates all the features of standard Deep Red enclosures with the addition of the coaxial mounted AX-HI 1" titanium compression high frequency driver and crossover network. Extending the frequency response to the upper audible limits, the AX-HI driver projects highs smoothly, and widely disperses them directly from the center of the cone driver. A deep red dome signifies the AX-HI driver is present, but actually all you need is one listen and you will know it's there.

Recommended amplifier size: Amplifiers will vary greatly from different manufacturers. The amplifiers output power rating is only one part of the information required to chose an amplifier for your system. Different amplifiers with the same output power rating will sound different and have various feelings of power and fidelity. Added to this are the various playing styles and techniques of the individual musician that will use various degrees of dynamic range. With a playing style utilizing wide dynamic range you may successfully choose the higher power rating, while a hard driving rock style would be safer choosing the lower power rating and adding additional speakers as required for a high output system. A system limiter is always a good choice to prevent the power amplifier from clipping which can both sound bad and cause speaker damage.

Frequency Response: The DEEP RED systems are designed especially for live musical instruments. They are not "flat", but have been tuned to be ideal. The frequency response specification is +/- 6 dB. The +/- 6 dB points mark the useful frequency range of the system. This is the range that responds well to the various equalizers and tone controls found on typical instrument amps and preamps.

The Deep Red Sub incorporates BAG END INFRA technology to extend the frequency response as low as 18 hertz. With the capabilities to provide flat frequency response well below the audible range of human hearing the DEEP RED SUB can quickly and accurately reproduce the entire fundamental spectrum of any bass instrument. The system will perform well with conventional crossovers in a bi-amped configuration but to really experience the maximum fidelity and output use in conjunction with the INFRA electronic crossover. The Deep Red SUB systems are designed to be bi-amped, requiring a dedicated amplifier channel for the sub and the upper range system.

For 20 years Bag End has been using the multi ply birch plywood from the upper baltic region in Europe, well known as the region producing the highest quality plywood in the world. Bag End has selected the finest grade of this superior material to produce the Natural Wood enclosures. Beautiful and yet rugged and roadworthy, designed and built to last a lifetime, the Natural Wood series offers the quality and performance that has made Bag End bass systems a popular choice among professionals.

The INFRA M2 is an electronic crossover featuring dual integrated INFRA low frequency output and stereo hi Pass outputs. The front panel controls include low and high frequency gain and system protection threshold. The INFRA-M2 includes INFRA Dynamic Filter protection and Hi frequency CVR limiter protection. The INFRA-M2 will enhance any bi-amped system using a Deep Red SUB enclosure.

Bag End loudspeaker systems are designed around several standard dimensions allowing for the stacking of various system configurations. Only your imagination will limit the variety of possible system designs, ranging from a small portable system, a larger bi-amped and even a stereo bi-amped system. Often a larger system may be broken down into several smaller systems for rehearsals, recording sessions and smaller gigs. Bag End's commitment to standards and modularity allows for stacking and acoustical compatibility between current and past models to insure the ability to build larger systems over time without replacing original units.

A system including both the INFRA low frequency and AX-HI high frequency technology responds beyond human hearing in both directions. A flat smooth response throughout the midrange insures that instruments are reproduced without coloration or distortion.

Once you own a Bag End modular system you'll may never be satisfied with standard bass amps again.

INFRA, Deep Red, Deep Red X, Deep Red SUB, Natural Wood and BAG END are registered trademarks of Modular Sound Systems Inc.

Bag End D10BX-D 2x10 Bass Cabinet Specifications:

• Dimensions: 18.5"h x 22.5"w x 18.5"d
• Weight: 70 lbs.

Bag End D10BX-D 2x10 Bass Cabinet Features:

• Transducers: 2-10" cones, coaxial AX-HI drive
• Input connectors: Dual banana, 2 1/4" phone,
• 2 Neutrik Speakon NL4MP
• Impedance: 4 Ohms
• Power handling: 400 Watts continuous sine wave
• 1600 Watts instantaneous peak

A Bag End modular loudspeaker system is a professional's choice. Order today.

Punchy, deep, and clean.

The versatile Q10BX-D speaker cab is ideal for electric bass guitar, acoustic bass, electric guitar, and the Chapman Stick.

The Deep Red series cabinets combine Bag End's long standing acoustical designs for bass instruments with modern state of the art materials and production techniques. The subtle deep red color blends toward black at a distance but up close it radiates a subtle deep ruby red color. Under the carpet the speaker enclosure is made from the finest void free hardwood plywood and incorporates precision-machined joints and modern adhesives for unsurpassed road worthiness.

The Deep Red X series incorporates all the features of standard Deep Red enclosures with the addition of the coaxial mounted AX-HI 1" titanium compression high frequency driver and crossover network. Extending the frequency response to the upper audible limits, the AX-HI driver projects highs smoothly, and widely disperses them directly from the center of the cone driver. A deep red dome signifies the AX-HI driver is present, but actually all you need is one listen and you will know it's there.

Recommended amplifier size: Amplifiers will vary greatly from different manufacturers. The amplifiers output power rating is only one part of the information required to chose an amplifier for your system. Different amplifiers with the same output power rating will sound different and have various feelings of power and fidelity. Added to this are the various playing styles and techniques of the individual musician that will use various degrees of dynamic range. With a playing style utilizing wide dynamic range you may successfully choose the higher power rating, while a hard driving rock style would be safer choosing the lower power rating and adding additional speakers as required for a high output system. A system limiter is always a good choice to prevent the power amplifier from clipping which can both sound bad and cause speaker damage.

Frequency Response: The DEEP RED systems are designed especially for live musical instruments. They are not "flat", but have been tuned to be ideal. The frequency response specification is +/- 6 dB. The +/- 6 dB points mark the useful frequency range of the system. This is the range that responds well to the various equalizers and tone controls found on typical instrument amps and preamps.

The Deep Red Sub incorporates BAG END INFRA technology to extend the frequency response as low as 18 hertz. With the capabilities to provide flat frequency response well below the audible range of human hearing the DEEP RED SUB can quickly and accurately reproduce the entire fundamental spectrum of any bass instrument. The system will perform well with conventional crossovers in a bi-amped configuration but to really experience the maximum fidelity and output use in conjunction with the INFRA electronic crossover. The Deep Red SUB systems are designed to be bi-amped, requiring a dedicated amplifier channel for the sub and the upper range system.

For 20 years Bag End has been using the multi ply birch plywood from the upper baltic region in Europe, well known as the region producing the highest quality plywood in the world. Bag End has selected the finest grade of this superior material to produce the Natural Wood enclosures. Beautiful and yet rugged and roadworthy, designed and built to last a lifetime, the Natural Wood series offers the quality and performance that has made Bag End bass systems a popular choice among professionals.

The INFRA M2 is an electronic crossover featuring dual integrated INFRA low frequency output and stereo hi Pass outputs. The front panel controls include low and high frequency gain and system protection threshold. The INFRA-M2 includes INFRA Dynamic Filter protection and Hi frequency CVR limiter protection. The INFRA-M2 will enhance any bi-amped system using a Deep Red SUB enclosure.

Bag End loudspeaker systems are designed around several standard dimensions allowing for the stacking of various system configurations. Only your imagination will limit the variety of possible system designs, ranging from a small portable system, a larger bi-amped and even a stereo bi-amped system. Often a larger system may be broken down into several smaller systems for rehearsals, recording sessions and smaller gigs. Bag End's commitment to standards and modularity allows for stacking and acoustical compatibility between current and past models to insure the ability to build larger systems over time without replacing original units.

A system including both the INFRA low frequency and AX-HI high frequency technology responds beyond human hearing in both directions. A flat smooth response throughout the midrange insures that instruments are reproduced without coloration or distortion.

Once you own a Bag End modular system you'll may never be satisfied with standard bass amps again.

INFRA, Deep Red, Deep Red X, Deep Red SUB, Natural Wood and BAG END are registered trademarks of Modular Sound Systems Inc.

Bag End Q10BX-D 4x10 Bass Cabinet Specifications:

• Dimensions: 28"h x 22.5"w x 18.5"d
• Weight: 96 lbs.

Bag End Q10BX-D 4x10 Bass Cabinet Features:

• Transducers: 4-10" cones, coaxial AX-HI drive
• Input connectors: Dual banana, 2-1/4" phone,
• 2-Neutrik Speakon NL4MP
• Impedance: 8 Ohms
• Power handling: 800 Watts continuous sine wave
• 3200 Watts instantaneous peak

A Bag End modular loudspeaker system is a professional's choice. Order today.

A oro-quality cab ideal for many applications.

The versatile S10X-D speaker cab is a great cab for electric bass guitar, acoustic bass, electric guitar, and the Chapman Stick.

The Deep Red series combines Bag End's long standing acoustical designs for bass instruments with modern state of the art materials and production techniques. The subtle deep red color blends toward black at a distance but up close it radiates a subtle deep ruby red color. Under the carpet the speaker enclosure is made from the finest void free hardwood plywood and incorporates precision-machined joints and modern adhesives for unsurpassed road worthiness.

The Deep Red X series incorporates all the features of standard Deep Red enclosures with the addition of the coaxial mounted AX-HI 1" titanium compression high frequency driver and crossover network. Extending the frequency response to the upper audible limits, the AX-HI driver projects highs smoothly, and widely disperses them directly from the center of the cone driver. A deep red dome signifies the AX-HI driver is present, but actually all you need is one listen and you will know it's there.

Recommended amplifier size: Amplifiers will vary greatly from different manufacturers. The amplifiers output power rating is only one part of the information required to chose an amplifier for your system. Different amplifiers with the same output power rating will sound different and have various feelings of power and fidelity. Added to this are the various playing styles and techniques of the individual musician that will use various degrees of dynamic range. With a playing style utilizing wide dynamic range you may successfully choose the higher power rating, while a hard driving rock style would be safer choosing the lower power rating and adding additional speakers as required for a high output system. A system limiter is always a good choice to prevent the power amplifier from clipping which can both sound bad and cause speaker damage.

Frequency Response: The DEEP RED systems are designed especially for live musical instruments. They are not "flat", but have been tuned to be ideal. The frequency response specification is +/- 6 dB. The +/- 6 dB points mark the useful frequency range of the system. This is the range that responds well to the various equalizers and tone controls found on typical instrument amps and preamps.

The Deep Red Sub incorporates BAG END INFRA technology to extend the frequency response as low as 18 hertz. With the capabilities to provide flat frequency response well below the audible range of human hearing the DEEP RED SUB can quickly and accurately reproduce the entire fundamental spectrum of any bass instrument. The system will perform well with conventional crossovers in a bi-amped configuration but to really experience the maximum fidelity and output use in conjunction with the INFRA electronic crossover. The Deep Red SUB systems are designed to be bi-amped, requiring a dedicated amplifier channel for the sub and the upper range system.

For 20 years Bag End has been using the multi ply birch plywood from the upper baltic region in Europe, well known as the region producing the highest quality plywood in the world. Bag End has selected the finest grade of this superior material to produce the Natural Wood enclosures. Beautiful and yet rugged and roadworthy, designed and built to last a lifetime, the Natural Wood series offers the quality and performance that has made Bag End bass systems a popular choice among professionals.

The INFRA M2 is an electronic crossover featuring dual integrated INFRA low frequency output and stereo hi Pass outputs. The front panel controls include low and high frequency gain and system protection threshold. The INFRA-M2 includes INFRA Dynamic Filter protection and Hi frequency CVR limiter protection. The INFRA-M2 will enhance any bi-amped system using a Deep Red SUB enclosure.

Bag End loudspeaker systems are designed around several standard dimensions allowing for the stacking of various system configurations. Only your imagination will limit the variety of possible system designs, ranging from a small portable system, a larger bi-amped and even a stereo bi-amped system. Often a larger system may be broken down into several smaller systems for rehearsals, recording sessions and smaller gigs. Bag End's commitment to standards and modularity allows for stacking and acoustical compatibility between current and past models to insure the ability to build larger systems over time without replacing original units.

A system including both the INFRA low frequency and AX-HI high frequency technology responds beyond human hearing in both directions. A flat smooth response throughout the midrange insures that instruments are reproduced without coloration or distortion.

Once you own a Bag End modular system you'll may never be satisfied with standard bass amps again.

INFRA, Deep Red, Deep Red X, Deep Red SUB, Natural Wood and BAG END are registered trademarks of Modular Sound Systems Inc.

Bag End S10X-D 1x10 Bass Cabinet Specifications:

• 13.5"h x 14.5"w x 12"d

Bag End S10X-D 1x10 Bass Cabinet Features:

• Transducers: 10" cone
• Input connectors: Dual banana, 2-1/4" phone
• Impedance: 8 Ohms
• Power handling: 200 Watts continuous sine wave
• 800 Watts instantaneous peak
• Dimensions: 13.5"h x 14.5"w x 12"d
• Weight: 27 lbs.

A Bag End modular loudspeaker system is a professional's choice. Order today.

The versatile S12-D is ideal for electric bass guitar, acoustic bass, electric guitar, and the Chapman Stick.

The Deep Red series combines Bag End's long standing acoustical designs for bass instruments with modern state of the art materials and production techniques. The subtle deep red color blends toward black at a distance but up close it radiates a subtle deep ruby red color. Under the carpet the enclosure is made from the finest void free hardwood plywood and incorporates precision-machined joints and modern adhesives for unsurpassed road worthiness.

The Deep Red X series incorporates all the features of standard Deep Red enclosures with the addition of the coaxial mounted AX-HI 1" titanium compression high frequency driver and crossover network. Extending the frequency response to the upper audible limits, the AX-HI driver projects highs smoothly, and widely disperses them directly from the center of the cone driver. A deep red dome signifies the AX-HI driver is present, but actually all you need is one listen and you will know it's there.

Recommended amplifier size: Amplifiers will vary greatly from different manufacturers. The amplifiers output power rating is only one part of the information required to chose an amplifier for your system. Different amplifiers with the same output power rating will sound different and have various feelings of power and fidelity. Added to this are the various playing styles and techniques of the individual musician that will use various degrees of dynamic range. With a playing style utilizing wide dynamic range you may successfully choose the higher power rating, while a hard driving rock style would be safer choosing the lower power rating and adding additional speakers as required for a high output system. A system limiter is always a good choice to prevent the power amplifier from clipping which can both sound bad and cause speaker damage.

Frequency Response: The DEEP RED systems are designed especially for live musical instruments. They are not "flat", but have been tuned to be ideal. The frequency response specification is +/- 6 dB. The +/- 6 dB points mark the useful frequency range of the system. This is the range that responds well to the various equalizers and tone controls found on typical instrument amps and preamps.

The Deep Red Sub incorporates BAG END INFRA technology to extend the frequency response as low as 18 hertz. With the capabilities to provide flat frequency response well below the audible range of human hearing the DEEP RED SUB can quickly and accurately reproduce the entire fundamental spectrum of any bass instrument. The system will perform well with conventional crossovers in a bi-amped configuration but to really experience the maximum fidelity and output use in conjunction with the INFRA electronic crossover. The Deep Red SUB systems are designed to be bi-amped, requiring a dedicated amplifier channel for the sub and the upper range system.

For 20 years Bag End has been using the multi ply birch plywood from the upper baltic region in Europe, well known as the region producing the highest quality plywood in the world. Bag End has selected the finest grade of this superior material to produce the Natural Wood enclosures. Beautiful and yet rugged and roadworthy, designed and built to last a lifetime, the Natural Wood series offers the quality and performance that has made Bag End bass systems a popular choice among professionals.

The INFRA M2 is an electronic crossover featuring dual integrated INFRA low frequency output and stereo hi Pass outputs. The front panel controls include low and high frequency gain and system protection threshold. The INFRA-M2 includes INFRA Dynamic Filter protection and Hi frequency CVR limiter protection. The INFRA-M2 will enhance any bi-amped system using a Deep Red SUB enclosure.

Bag End loudspeaker systems are designed around several standard dimensions allowing for the stacking of various system configurations. Only your imagination will limit the variety of possible system designs, ranging from a small portable system, a larger bi-amped and even a stereo bi-amped system. Often a larger system may be broken down into several smaller systems for rehearsals, recording sessions and smaller gigs. Bag End's commitment to standards and modularity allows for stacking and acoustical compatibility between current and past models to insure the ability to build larger systems over time without replacing original units.

A system including both the INFRA low frequency and AX-HI high frequency technology responds beyond human hearing in both directions. A flat smooth response throughout the midrange insures that instruments are reproduced without coloration or distortion.

Once you own a Bag End modular system you'll may never be satisfied with standard bass amps again.

INFRA, Deep Red, Deep Red X, Deep Red SUB, Natural Wood and BAG END are registered trademarks of Modular Sound Systems Inc.

Bag End S12-D 1x12 Bass Cabinet Specifications:

• Dimensions: 15.5"h x 18.5"w x 15.5"d
• Weight: 41 lbs.

Bag End S12-D 1x12 Bass Cabinet Features:

• Transducer: 12" cone
• Input connectors: Dual banana, 2-1/4" phone
• Impedance: 8 Ohms
• Power handling: 200 Watts continuous sine wave
• 800 Watts instantaneous peak

A Bag End modular loudspeaker system is a professional's choice. Order today.

Compact but still capable of big, deep bass tone.

The versatile S15LX-D speaker cab is ideal for electric bass guitar, acoustic bass, electric guitar, and the Chapman Stick.

The Deep Red series combines Bag End's long standing acoustical designs for bass instruments with modern state of the art materials and production techniques. The subtle deep red color blends toward black at a distance but up close it radiates a subtle deep ruby red color. Under the carpet the speaker enclosure is made from the finest void free hardwood plywood and incorporates precision-machined joints and modern adhesives for unsurpassed road worthiness.

The Deep Red X series cabinets incorporate all the features of standard Deep Red enclosures with the addition of the coaxial mounted AX-HI 1" titanium compression high frequency driver and crossover network. Extending the frequency response to the upper audible limits, the AX-HI driver projects highs smoothly, and widely disperses them directly from the center of the cone driver. A deep red dome signifies the AX-HI driver is present, but actually all you need is one listen and you will know it's there.

Recommended amplifier size: Amplifiers will vary greatly from different manufacturers. The amplifiers output power rating is only one part of the information required to chose an amplifier for your system. Different amplifiers with the same output power rating will sound different and have various feelings of power and fidelity. Added to this are the various playing styles and techniques of the individual musician that will use various degrees of dynamic range. With a playing style utilizing wide dynamic range you may successfully choose the higher power rating, while a hard driving rock style would be safer choosing the lower power rating and adding additional speakers as required for a high output system. A system limiter is always a good choice to prevent the power amplifier from clipping which can both sound bad and cause speaker damage.

Frequency Response: The DEEP RED systems are designed especially for live musical instruments. They are not "flat", but have been tuned to be ideal. The frequency response specification is +/- 6 dB. The +/- 6 dB points mark the useful frequency range of the system. This is the range that responds well to the various equalizers and tone controls found on typical instrument amps and preamps.

The Deep Red Sub incorporates BAG END INFRA technology to extend the frequency response as low as 18 hertz. With the capabilities to provide flat frequency response well below the audible range of human hearing the DEEP RED SUB can quickly and accurately reproduce the entire fundamental spectrum of any bass instrument. The system will perform well with conventional crossovers in a bi-amped configuration but to really experience the maximum fidelity and output use in conjunction with the INFRA electronic crossover. The Deep Red SUB systems are designed to be bi-amped, requiring a dedicated amplifier channel for the sub and the upper range system.

For 20 years Bag End has been using the multi ply birch plywood from the upper baltic region in Europe, well known as the region producing the highest quality plywood in the world. Bag End has selected the finest grade of this superior material to produce the Natural Wood enclosures. Beautiful and yet rugged and roadworthy, designed and built to last a lifetime, the Natural Wood series offers the quality and performance that has made Bag End bass systems a popular choice among professionals.

The INFRA M2 is an electronic crossover featuring dual integrated INFRA low frequency output and stereo hi Pass outputs. The front panel controls include low and high frequency gain and system protection threshold. The INFRA-M2 includes INFRA Dynamic Filter protection and Hi frequency CVR limiter protection. The INFRA-M2 will enhance any bi-amped system using a Deep Red SUB enclosure.

Bag End loudspeaker systems are designed around several standard dimensions allowing for the stacking of various system configurations. Only your imagination will limit the variety of possible system designs, ranging from a small portable system, a larger bi-amped and even a stereo bi-amped system. Often a larger system may be broken down into several smaller systems for rehearsals, recording sessions and smaller gigs. Bag End's commitment to standards and modularity allows for stacking and acoustical compatibility between current and past models to insure the ability to build larger systems over time without replacing original units.

A system including both the INFRA low frequency and AX-HI high frequency technology responds beyond human hearing in both directions. A flat smooth response throughout the midrange insures that instruments are reproduced without coloration or distortion.

Once you own a Bag End modular system you'll may never be satisfied with standard bass amps again.

INFRA, Deep Red, Deep Red X, Deep Red SUB, Natural Wood and BAG END are registered trademarks of Modular Sound Systems Inc.

Bag End S15LX-D 1x15 Bass Cabinet Specifications:

• Dimensions: 15.5"h x 18.5"w x 15.5"d
• Weight: 41 lbs.

Bag End S15LX-D 1x15 Bass Cabinet Features:

• Transducer: 12" cone
• Input connectors: Dual banana, 2-1/4" phone
• Impedance: 8 Ohms
• Power handling: 200 Watts continuous sine wave
• 800 Watts instantaneous peak

A Bag End bass cab is a totally professional choice. Order yours today.

A speaker worthy of the finest amps.

The versatile S15X-D is ideal for electric bass guitar, acoustic bass, electric guitar, and the Chapman Stick.

The Deep Red series combines Bag End's long standing acoustical designs for bass instruments with modern state of the art materials and production techniques. The subtle deep red color blends toward black at a distance but up close it radiates a subtle deep ruby red color. Under the carpet the enclosure is made from the finest void free hardwood plywood and incorporates precision-machined joints and modern adhesives for unsurpassed road worthiness.

The Deep Red X series incorporates all the features of standard Deep Red enclosures with the addition of the coaxial mounted AX-HI 1" titanium compression high frequency driver and crossover network. Extending the frequency response to the upper audible limits, the AX-HI driver projects highs smoothly, and widely disperses them directly from the center of the cone driver. A deep red dome signifies the AX-HI driver is present, but actually all you need is one listen and you will know it's there.

Recommended amplifier size: Amplifiers will vary greatly from different manufacturers. The amplifiers output power rating is only one part of the information required to chose an amplifier for your system. Different amplifiers with the same output power rating will sound different and have various feelings of power and fidelity. Added to this are the various playing styles and techniques of the individual musician that will use various degrees of dynamic range. With a playing style utilizing wide dynamic range you may successfully choose the higher power rating, while a hard driving rock style would be safer choosing the lower power rating and adding additional speakers as required for a high output system. A system limiter is always a good choice to prevent the power amplifier from clipping which can both sound bad and cause speaker damage.

Frequency Response: The DEEP RED systems are designed especially for live musical instruments. They are not "flat", but have been tuned to be ideal. The frequency response specification is +/- 6 dB. The +/- 6 dB points mark the useful frequency range of the system. This is the range that responds well to the various equalizers and tone controls found on typical instrument amps and preamps.

The Deep Red Sub incorporates BAG END INFRA technology to extend the frequency response as low as 18 hertz. With the capabilities to provide flat frequency response well below the audible range of human hearing the DEEP RED SUB can quickly and accurately reproduce the entire fundamental spectrum of any bass instrument. The system will perform well with conventional crossovers in a bi-amped configuration but to really experience the maximum fidelity and output use in conjunction with the INFRA electronic crossover. The Deep Red SUB systems are designed to be bi-amped, requiring a dedicated amplifier channel for the sub and the upper range system.

For 20 years Bag End has been using the multi ply birch plywood from the upper baltic region in Europe, well known as the region producing the highest quality plywood in the world. Bag End has selected the finest grade of this superior material to produce the Natural Wood enclosures. Beautiful and yet rugged and roadworthy, designed and built to last a lifetime, the Natural Wood series offers the quality and performance that has made Bag End bass systems a popular choice among professionals.

The INFRA M2 is an electronic crossover featuring dual integrated INFRA low frequency output and stereo hi Pass outputs. The front panel controls include low and high frequency gain and system protection threshold. The INFRA-M2 includes INFRA Dynamic Filter protection and Hi frequency CVR limiter protection. The INFRA-M2 will enhance any bi-amped system using a Deep Red SUB enclosure.

Bag End loudspeaker systems are designed around several standard dimensions allowing for the stacking of various system configurations. Only your imagination will limit the variety of possible system designs, ranging from a small portable system, a larger bi-amped and even a stereo bi-amped system. Often a larger system may be broken down into several smaller systems for rehearsals, recording sessions and smaller gigs. Bag End's commitment to standards and modularity allows for stacking and acoustical compatibility between current and past models to insure the ability to build larger systems over time without replacing original units.

A system including both the INFRA low frequency and AX-HI high frequency technology responds beyond human hearing in both directions. A flat smooth response throughout the midrange insures that instruments are reproduced without coloration or distortion.

Once you own a Bag End modular system you'll may never be satisfied with standard bass amps again.

INFRA, Deep Red, Deep Red X, Deep Red SUB, Natural Wood and BAG END are registered trademarks of Modular Sound Systems Inc.

Bag End S15X-D 1x15 Bass Cabinet Specifications:

• Transducer: 15" cone
• Dimensions: 18.5"h x 18.5"w x 15.5"d
• Weight: 44 lbs. (with AX-HI drive add 6 lbs.)

Bag End S15X-D 1x15 Bass Cabinet Features:

• Input connectors:
• Dual banana, 2-1/4" phone
• (15X includes 2-Neutrik Speakon NL4MP
• Impedance: 8 Ohms
• Power handling: 200 Watts continuous sine wave
• 800 Watts instantaneous peak

A Bag End modular loudspeaker system is a professional's choice. Order today.

The ultimate in efficiency and sonic excellence.

The versatile S18B-D speaker cab is ideal for electric bass guitar, acoustic bass, electric guitar, and the Chapman Stick.

The Deep Red series combines Bag End's long standing acoustical designs for bass instruments with modern state of the art materials and production techniques. The subtle deep red color blends toward black at a distance but up close it radiates a subtle deep ruby red color. Under the carpet the speaker enclosure is made from the finest void free hardwood plywood and incorporates precision-machined joints and modern adhesives for unsurpassed road worthiness.

The Deep Red X series cabinets incorporate all the features of standard Deep Red enclosures with the addition of the coaxial mounted AX-HI 1" titanium compression high frequency driver and crossover network. Extending the frequency response to the upper audible limits, the AX-HI driver projects highs smoothly, and widely disperses them directly from the center of the cone driver. A deep red dome signifies the AX-HI driver is present, but actually all you need is one listen and you will know it's there.

Recommended amplifier size: Amplifiers will vary greatly from different manufacturers. The amplifiers output power rating is only one part of the information required to chose an amplifier for your system. Different amplifiers with the same output power rating will sound different and have various feelings of power and fidelity. Added to this are the various playing styles and techniques of the individual musician that will use various degrees of dynamic range. With a playing style utilizing wide dynamic range you may successfully choose the higher power rating, while a hard driving rock style would be safer choosing the lower power rating and adding additional speakers as required for a high output system. A system limiter is always a good choice to prevent the power amplifier from clipping which can both sound bad and cause speaker damage.

Frequency Response: The DEEP RED systems are designed especially for live musical instruments. They are not "flat", but have been tuned to be ideal. The frequency response specification is +/- 6 dB. The +/- 6 dB points mark the useful frequency range of the system. This is the range that responds well to the various equalizers and tone controls found on typical instrument amps and preamps.

The Deep Red Sub incorporates BAG END INFRA technology to extend the frequency response as low as 18 hertz. With the capabilities to provide flat frequency response well below the audible range of human hearing the DEEP RED SUB can quickly and accurately reproduce the entire fundamental spectrum of any bass instrument. The system will perform well with conventional crossovers in a bi-amped configuration but to really experience the maximum fidelity and output use in conjunction with the INFRA electronic crossover. The Deep Red SUB systems are designed to be bi-amped, requiring a dedicated amplifier channel for the sub and the upper range system.

For 20 years Bag End has been using the multi ply birch plywood from the upper baltic region in Europe, well known as the region producing the highest quality plywood in the world. Bag End has selected the finest grade of this superior material to produce the Natural Wood enclosures. Beautiful and yet rugged and roadworthy, designed and built to last a lifetime, the Natural Wood series offers the quality and performance that has made Bag End bass systems a popular choice among professionals.

The INFRA M2 is an electronic crossover featuring dual integrated INFRA low frequency output and stereo hi Pass outputs. The front panel controls include low and high frequency gain and system protection threshold. The INFRA-M2 includes INFRA Dynamic Filter protection and Hi frequency CVR limiter protection. The INFRA-M2 will enhance any bi-amped system using a Deep Red SUB enclosure.

Bag End loudspeaker systems are designed around several standard dimensions allowing for the stacking of various system configurations. Only your imagination will limit the variety of possible system designs, ranging from a small portable system, a larger bi-amped and even a stereo bi-amped system. Often a larger system may be broken down into several smaller systems for rehearsals, recording sessions and smaller gigs. Bag End's commitment to standards and modularity allows for stacking and acoustical compatibility between current and past models to insure the ability to build larger systems over time without replacing original units.

A system including both the INFRA low frequency and AX-HI high frequency technology responds beyond human hearing in both directions. A flat smooth response throughout the midrange insures that instruments are reproduced without coloration or distortion.

Once you own a Bag End modular system you'll may never be satisfied with standard bass amps again.

INFRA, Deep Red, Deep Red X, Deep Red SUB, Natural Wood and BAG END are registered trademarks of Modular Sound Systems Inc.

Bag End S18B-D 1x18 Bass Cabinet Specifications:

• Dimensions: 22.5"h x 30"w x 20.5"d
• Weight: 73 lbs.

Bag End S18B-D 1x18 Bass Cabinet Features:

• Transducer: 18" cone
• Input connectors: Dual banana, 2-1/4" phone
• Impedance: 8 Ohms
• Power handling: 300 Watts continuous sine wave
• 1200 Watts instantaneous peak

A Bag End modular loudspeaker system is a professional's choice. Order today.

Solid cab with plenty of crunch.

The Basson 300W, 8-ohm bottom-ported bass cab features a 15" Eminence Delta driver and a horn. Accentuates midrange sweetness, yet still lingers low to drive the bass line. The B15B is very articulate with punchy yet smooth and balanced low end. Features a "bell" tone that is big on the bottom but very clear through the mids and highs. Quality Basson craftsmanship includes durable carpet-covered cabinet, 1-1/4" braced reinforcement of all joints, and recessed steel handles. The cab is sealed air tight for amazing punch. 40Hz-4kHz frequency response.

Basson B15B 300W Bass Cabinet with 1x15 Speaker and Horn Specifications:

• 15" Eminence Delta driver
• Horn
• 300W rms
• 8 ohms
• 98dB max-120dB
• 40Hz-4kHz frequency response
• 24-1/4"W x 30-1/4"H x 18-1/4"D
• 84 lbs.

Basson B15B 300W Bass Cabinet with 1x15 Speaker and Horn Features:

• Durable carpet covered cabinet
• Balanced quality tones
• All joints reinforced with 1-1/4" braces
• Steel recessed metal handles for durability
• 2 - 1/4" inputs
• Sealed air tight for amazing punch
• 5-year warranty

Loud, clear, thunderous bass can be yours today!

Versatile bass amp puts out amazing volume and tone.

The Basson B210B's unique tone comes from 2 - 10" bass speakers with magnets weighing in at 13 pounds each and a deep 28Hz-5kHz frequency response. The most obvious aspect of that tone is the resonant low end, which is sustained effortlessly at 500W RMS. The overall sound is very warm, yet well articulated. A tweeter switch makes this cabinet very versatile.

This is a power-hungry brute, thus your head choice is critical and must sustain 400+ watts at 4 ohms. Features removable ball-bearing casters, a big plus when gigging. Quality Basson craftsmanship includes durable carpet-covered cabinet, 1-1/4" bracing to reinforce all joints, and recessed steel handles. The cab is sealed air tight for enhanced punch.

Basson B210B 500W Bass Cabinet with 2x10 Speakers and Horn Specifications:

• 2x10" BS1075 driver
• Horn with on/off switch
• 500W RMS
• 101dB max-125dB
• 4 ohms
• 28Hz-5kHz frequency response
• 24-1/4"W x 33-1/4"H x 18-1/4"D
• 110 lbs.

Basson B210B 500W Bass Cabinet with 2x10 Speakers and Horn Features:

• Durable carpet-covered cabinet
• Balanced tone
• Incredible low end
• All joints reinforced with 1-1/4" braces
• Steel recessed metal handles for durability
• 2 Speakon jacks
• Removable heavy-duty casters
• Sealed air tight for amazing punch
• 5-year warranty

Look no further-this is THE bass cab you've been dreaming of.

Monster low end response in a cab built like a tank.

Basson's 4x10 bass cab has the same heavy magnet speakers as the B210B and the B810B for a similar unique tone that's slightly more aggressive than the B210B. The B410B produces sub-harmonics down to 28Hz, uncharacteristic of other 4x10" bass cabs. The result is like "warm thunder." The oversized 200-oz. speaker magnets and 1,000 watts RMS power handling keep the cones moving lots of air, increasing sustain and volume with longer wavelengths for massive low end.

This cab is a power-hungry animal and will need an amp rated at 750+ watts at 8 ohms. Also features a tweeter switch and ball-bearing casters. Quality Basson craftsmanship includes a durable carpet-covered cabinet with 1-1/4" bracing to reinforce all joints and recessed steel handles. The cab is sealed air tight for amazing punch.

Basson B410B 1,000W Bass Cabinet with 4x10 Speaker and Horn Specifications:

• 4 - 10" BS1075 drivers with 200-oz. magnet
• Horn with on/off switch
• 1,000W RMS handling
• 28Hz-5kHz frequency response
• 103dB max-130dB
• 8 ohms
• 28-5/8"W x 35-1/4"H x 17-1/4"D
• 148 lbs.

Basson B410B 1,000W Bass Cabinet with 4x10 Speaker and Horn Features:

• Durable carpet covered cabinet
• Balanced quality tones
• Incredible low end
• All joints reinforced with 1-1/4" braces
• Recessed steel handles for durability
• 2 Speakon jacks
• Removable heavy-duty casters
• Sealed air tight for amazing punch
• 5-year warranty

Incredible sound and a booming 1,000W! Order today and see for yourself!

Monster low end response in a cab built like a tank.

Basson's 4x10 bass cab has the same heavy magnet speakers as the B210B and the B810B for a similar unique tone that's slightly more aggressive than the B210B. The B410B produces sub-harmonics down to 28Hz, uncharacteristic of other 4x10" bass cabs. The result is like "warm thunder." The oversized 200-oz. speaker magnets and 1,000 watts RMS power handling keep the cones moving lots of air, increasing sustain and volume with longer wavelengths for massive low end.

This cab is a power-hungry animal and will need an amp rated at 750+ watts at 8 ohms. Also features a tweeter switch and ball-bearing casters. Quality Basson craftsmanship includes a durable carpet-covered cabinet with 1-1/4" bracing to reinforce all joints and recessed steel handles. The cab is sealed air tight for amazing punch.

Basson B410B 1,000W Bass Cabinet with 4x10 Speaker and Horn - Scratch 'n' Dent Specifications:

• 4 - 10" BS1075 drivers with 200-oz. magnet
• Horn with on/off switch
• 1,000W RMS handling
• 28Hz-5kHz frequency response
• 103dB max-130dB
• 8 ohms
• 28-5/8"W x 35-1/4"H x 17-1/4"D
• 148 lbs.

Basson B410B 1,000W Bass Cabinet with 4x10 Speaker and Horn - Scratch 'n' Dent Features:

• Durable carpet covered cabinet
• Balanced quality tones
• Incredible low end
• All joints reinforced with 1-1/4" braces
• Recessed steel handles for durability
• 2 Speakon jacks
• Removable heavy-duty casters
• Sealed air tight for amazing punch
• 5-year warranty

Incredible sound and a booming 1,000W! Order today and see for yourself!

'Pure Evil.'
-Nikki Sixx

The Basson B810B handles 2,000W of mean, gut-pounding bass. Its tone is extremely aggressive, reaching all the way down to 28Hz. The B810B has similar fundamental warm sub-bass sustaining qualities as the B210B and B410B, but has a subtle growl that begs to be pushed. This beast blends naturally with heavy guitars, yet remains a powerful statement in any musical context. This is the most brutal cab in Basson's line of bass cabinets weighing in at nearly 230 lbs. with 8 - 10" BS1075 drivers with 200oz. magnets and 2,000W RMS handling at 4 ohms. Amp choice is critical and must run at 1,500 watts per channel at 4 ohms minimum. Features 1-1/2"-wide grab bar and fixed casters. Quality Basson craftsmanship includes a durable carpet-covered cabinet with 1-1/4" bracing to reinforce all joints and steel recessed handles. The cab is sealed air tight for amazing punch.

Basson B810B 2,000W Bass Cabinet with 8x10 Speaker Specifications:

• 8x10" BS1075 drivers with 200oz. magnet
• 2000W RMS handling
• 105dB max
• -130dB
• 4 ohms
• 28Hz-5kHz frequency response
• 26-1/4"W x 55"H x 18"D
• 228 lbs.

Basson B810B 2,000W Bass Cabinet with 8x10 Speaker Features:

• Durable carpet covered cabinet
• Balanced quality tones with incredible low end
• Joints reinforced with 1-1/4" braces
• Steel recessed metal handles for durability
• Skid rails on back
• Sealed air tight for amazing punch
• 2 Speakon jacks
• 5-year warranty

2,000 watts of relentlessly pounding bass! Order today!

Raw power with sophisticated tonal controls.

This Behringer half stack includes The BX4500H Ultrabass amplifier head and the Ultrabass BA410 speaker cabinet.

The Behringer BX4500H Ultrabass Bass Head is amazingly versatile. The powerful 450W bass amplifier head features patented Dynamizer technology, a switchable Ultrabass sub-harmonics processor, and Behringer's revolutionary Shape filter for mid-band frequency control. The head also provides a dedicated 5-band EQ with Bright and Deep functions, a musical opto-limiter, vintage style VU meter, and XLR direct output.

You can select the Bright and Ultrabass functions with the supplied footswitch and insert an external EFX signal through the TRS effects send and return. 3 speaker outputs are available including TRS and Neutrik Speakon connections. Heat is controlled by a temperature controlled cooling system.

The Behringer Ultrabass BA410 1000W 4x10 Bass Cabinet has light, ultra-stiff aluminum cone speakers for fast response, incredible attack, and solid punch. The switchable 1" horn tweeter gives you as much high-end sizzle as you want. The tweeter also has a unique remote control feature that allows it to be controlled via footswitch or MIDI. Ample power handling (1,000W) gives you loads of headroom for a wide and rich response.

The heavy-duty speaker enclosure is constructed with reinforced internal speaker chambers, recessed carrying handles, integrated wheels for easy transportation, shockproof metal grille, reinforced corners, and rugged carpet covering. The cab is front-ported for deep bass response. I/O features 1/4" and Speakon connectors. 4 ohms impedance.

Behringer BX4500H and BA410 Half Stack Package Specifications:

• Behringer Ultrabass BA410 1000W 4x10 Bass Cabinet
  
  Frequency response: 40Hz-16kHz
• Dimensions: 25-4/5"W x 28-1/5"H x 16"D
• Weight: 102 lbs.

Behringer BX4500H and BA410 Half Stack Package Features:

• Behringer BX4500H Ultrabass Bass Head
  
  450W bass amplifier head
• Dynamizer technology
• Switchable Ultrabass sub-harmonics processor Shape filter for mid-band frequency control
• 5-band EQ with Bright and Deep functions Musical opto-limiter
• Vintage style VU meter
• XLR direct output
• Footswitch
• EFX loop (TRS effects send and return)
• 3 speaker outputs - (TRS and Neutrik Speakon connections)
• Temperature controlled cooling system
  
  Behringer Ultrabass BA410 1000W 4x10 Bass Cabinet
  
  1,000W power handling
• 4 - 10" aluminum cone speakers
• Switchable 1" horn tweeter
• Reinforced internal speaker chambers
• Front-ported bass cabinet
• Tweeter remote control via footswitch or MIDI
• 1/4" and Speakon connectors
• 4 ohms impedance
• Recessed carrying handles
• Integrated rollers
• Shockproof metal grille
• Reinforced corners
• Rugged carpet covering

Massive bass energy you can shape with a tap of the footswitch! Order now.

Raw power with sophisticated tonal controls.

The Behringer BX4500H Ultrabass Bass Head is amazingly versatile. The powerful 450W bass amplifier head features patented Dynamizer technology, a switchable Ultrabass sub-harmonics processor, and Behringer's revolutionary Shape filter for mid-band frequency control. The head also provides a dedicated 5-band EQ with Bright and Deep functions, a musical opto-limiter, vintage style VU meter, and XLR direct output.

You can select the Bright and Ultrabass functions with the supplied footswitch and insert an external EFX signal through the TRS effects send and return. 3 speaker outputs are available including TRS and Neutrik Speakon connections. Heat is controlled by a temperature controlled cooling system.

Behringer BX4500H Ultrabass Bass Head Features:

• 450W bass amplifier head
• Dynamizer technology
• Switchable Ultrabass sub-harmonics processor Shape filter for mid-band frequency control
• 5-band EQ with Bright and Deep functions Musical opto-limiter
• Vintage style VU meter
• XLR direct output
• Footswitch
• EFX loop (TRS effects send and return)
• 3 speaker outputs - (TRS and Neutrik Speakon connections)
• Temperature controlled cooling system

Massive bass energy you can shape with a tap of the footswitch! Order now.

Guitar/bass practice combo.

The Berhringer Thunderbird BX108 1x8" Bass Combo Amp is a little powerhouse that's ideal for practice and jamming. The Thunderbird bass combo boasts a 15W amp with a bass-reflex cabinet and custom-made 8" speaker. The cool retro design features a burgundy-colored top panel, black covering, and a leather handle. A 3-band EQ lets you shape the tone, and a stereo tape I/O makes it easy to interface the Behringer BX108 amp with your computer's soundcard.

Behringer Thunderbird BX108 1x8" Bass Combo Amp Specifications:

• 13"W x 14-1/2"H x 9-1/10"D
• 15-2/5 lbs.

Behringer Thunderbird BX108 1x8" Bass Combo Amp Features:

• 15W RMS bass practice combo with bass reflex cabinet
• Custom-made 8" speaker
• Cool retro design with burgundy top panel, black covering, and leather handle
• Level control plus great-sounding 3-band EQ
• Stereo tape I/O plus phones out

Use this amp to make your next hit record - DO IT TODAY AND SAVE!

Massive low frequency support and crisp attack.

If you're looking for floor-shaking bottom end, try the Behringer Ultrabass BA115 600 Watt 1x15 Bass Cabinet. Light, ultrastiff aluminum cone speaker packs fast response, incredible attack, and solid punch while the switchable 1" horn tweeter gives you as much high-end sizzle as you want. The tweeter also has a unique remote control feature that allows it to be controlled via footswitch or MIDI. Ample power handling (600W) gives you loads of headroom for a wide and rich response.

The heavy-duty cabinet is constructed with reinforced internal speaker chambers, recessed carrying handles, integrated wheels for easy transportation, shockproof metal grille, reinforced corners, and rugged carpet covering. Front-ported for deep bass response. I/O features 1/4" and Speakon connectors. 8 ohms impedance.

Behringer Ultrabass BA115 600 Watt 1x15 Bass Cabinet Specifications:

• Frequency response: 40Hz-16kHz
• Dimensions: 25-4/5"W x 25-4/5"H x 14-2/5"D
• Weight: 71 lbs.

Behringer Ultrabass BA115 600 Watt 1x15 Bass Cabinet Features:

• 600W power handling
• 1 - 15" aluminum cone speaker
• Switchable 1" horn tweeter
• Reinforced internal speaker chambers
• Front-ported bass cabinet
• Tweeter remote control via footswitch or MIDI
• 1/4" and Speakon connectors
• 8 ohms impedance
• Recessed carrying handles
• Integrated rollers
• Shock-proof metal grille
• Reinforced corners
• Rugged carpet covering

Get heavy with a 15' ported cabinet while still getting the sharp attack you crave. Order today.